Deco
Device: Deco X50 — HW v1.30, FW v1.3.1 Issue: IPv6 Not Working. PPPoE did not work in firmware versions v1.2.3 and v1.2.10, but it works in v1.3.1. However, IPv6 is still not functioning. My ISP canno
Network ConnectivityFirmware UpdateIPv6PPPoE
0Helpful
680Views
After the router updated to this version, some of the devices on my network stopped working. I tried different IPv6 settings, but to no avail. I had to disable IPv6 so I could continue using the netwo
Network ConnectivityFirmware UpdateIPv6
2Helpful
367Views
Hey TP-LINK !! Can you help me to configure IPV6 settings on Deco M4. I tried everything but Deco is not providing IPV6 to client devices but Deco is getting IPV6 from ISP ONT itself and when i do pin
IPv6
By
ARGamingPK1
· Latest post 2026-03-18 12:07:20
by ARGamingPK1
1Helpful
328Views
My connection uses IPv4 and IPv6 over PPPoE and my ISP sets Google IPs as the default IPv6 DNS servers. I run Pi-hole on Proxmox at 192.168.68.111. To avoid distributing an IPv6 DNS to clients, I conf
IPv6
2Helpful
446Views
Hello, I'm currently using the following configuration: ONU → DECO M5 (router mode) → Rakuten Casa 6. (M5 V2、Firmware：1.9.1 Build 20250909 Rel.37570) I've learned that in order to effectively use the
IPv6
3Helpful
280Views
Why does the Facebook app work fine on an iPhone connected to Deco, but not on a Mac using a web browser? The Mac is connected by both wifi and Ethernet. Disabling the Mac's wifi connection doesn't so
IPv6
By
Peter938029384
· Latest post 2025-10-15 10:05:33
by David-TP
0Helpful
202Views
Hello, I’ve been experiencing major internet issues for about a year. Initially, I was using 2 Deco M5 units, which I replaced a few days ago (X50 POE), thinking the problem came from that hardware. H
Network ConnectivityIPv6
2Helpful
976Views
Today i was trying to setup IPV6 on my Deco M4 but my Deco got IPV6 address and DNS but could'nt provide IPV6 address and DNS to connected clients and even i tried every options which are available on
IPv6
By
ARGamingPK1
· Latest post 2025-08-18 12:15:31
by ARGamingPK1
1Helpful
547Views
Hello, In the Deco app->More->Internet connection->IPv6->Internet parameters, if I set IPv6 to dynamic, I have the following choices for the whay to optin IPv6 addresses in French : "pare-feu", "sans
IPv6Network ConnectivityConnection PreferenceDeco App Related
2Helpful
1617Views
Hey TP-LINK !! Few days ago i turned ON (IPV6) on my Deco M4 in Router Mode and my all connected devices phones and tables got IPV6 connection and then IPV6 ip address gone and my IPV6 works only on B
IPv6
By
ARGamingPK1
· Latest post 2025-07-01 01:42:39
by ARGamingPK1
2Helpful
1826Views
Hi everyone, I own a Deco X20 AX1800 Mesh System, and I am trying to enable IPv6 and after enabling it, the router is unable to give IPv6 Addresses on the network. The ISP supports IPv6, I have confir
Network ConnectivityIPv6Prefix
By
audacityedits
· Latest post 2025-06-26 08:08:19
by David-TP
2Helpful
1710Views
I get the below errors and notices repeatedly, any ideas? Should I just ignore them? My deco is on 3G/4G Router mode. Thanks and regards Hakki Tue May 20 13:36:06 2025 user.err : dail_get_slaac_addr e
IPv6
1Helpful
508Views