Home Network Community > Wi-Fi Routers > Enable Hairpinning / NAT Loopback on Archer C5400X
< Wi-Fi Routers

Enable Hairpinning / NAT Loopback on Archer C5400X

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Enable Hairpinning / NAT Loopback on Archer C5400X

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Enable Hairpinning / NAT Loopback on Archer C5400X
Enable Hairpinning / NAT Loopback on Archer C5400X
2020-05-16 01:07:41
Model: Archer C5400X  
Hardware Version: V1
Firmware Version: 1.1.2 Build 20191223 rel.73956(5553)

I'm not able to connect to a service I've exposed via the "Virtual Servers" (port forwarding) feature using the external IP of my router.

This feature is known as hairpinning or NAT loopback and I haven't been able to find any setting to enable it within my router (Archer C5400X)'s settings.

 

Thanks!

  0      
 
  0      
 
#1
Options
5 Reply
Re:Enable Hairpinning / NAT Loopback on Archer C5400X
2020-05-16 04:26:13

Turning off NAT Boost in my router settings has enabled loopback to work and solved my issue.

  0  
  0  
#2
Options
Re:Enable Hairpinning / NAT Loopback on Archer C5400X
2020-05-17 03:41:50 - last edited 2020-05-17 03:42:57

@Lumin1a On my firmware version, I don't have a "NAT Boost" option at all.

 

Thank you for the suggestion though.

  0  
  0  
#3
Options
Re:Enable Hairpinning / NAT Loopback on Archer C5400X
2021-01-14 15:18:34

@An0n I know this thread is already over 6 months old, but I've had the same issue with my C5400X and am trying to figure out if there is any way to enable it. Did you have any luck figuring it out? I would have thought a router this expensive would have higher level networking functionality like this but maybe I'm just looking in the wrong place.

  0  
  0  
#4
Options
Re:Enable Hairpinning / NAT Loopback on Archer C5400X
2021-01-14 15:24:32

@Quartermain Not that I know of unfortunately :/

  0  
  0  
#5
Options
Re:Enable Hairpinning / NAT Loopback on Archer C5400X
2021-03-01 00:38:44

@Quartermain You're in the right place, unfortunately. We love TP-Link routers for their stability, however the firmware is lacking.

 

I was able to get NAT loopback partially working with my C5400X. The caveat: I had to access the device (LAN) via wifi. Kind of ridiculous, but it works until the firmware is fixed. :)

  0  
  0  
#6
Options

Information

Helpful: 0

Views: 8921

Replies: 5

Related Articles
 Archer C5400X NAT loopback
1385 0
Does the Archer A9 supports NAT Loopback/Hairpinning?
1877 0
 NAT-Loopback (Hairpinning)
615 0
Does TL-WR841N support nat loopback/hairpinning?
80 0
 Help with NAT Loopback/Hairpinning
80 0
Loopback (Hairpinning) on AX20
2010 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.