Home Network Community > Deco > Deco M9 plus speed capped at 100mbps on both wired and wireless
< Deco

Deco M9 plus speed capped at 100mbps on both wired and wireless

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Deco M9 plus speed capped at 100mbps on both wired and wireless

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco M9 plus speed capped at 100mbps on both wired and wireless
Deco M9 plus speed capped at 100mbps on both wired and wireless
2020-07-21 00:17:58 - last edited 2020-07-21 00:37:10
Model: Deco M9 Plus  
Hardware Version:
Firmware Version:

So I just got the deco M9 plus system yesterday because I was having coverage issues at my home and it seems to have fixed that which is great but I noticed something odd.

 

My Internet package is 250mbps download and upload and the maximum bandwidth I can get on the deco is always below 100mbps, on both wired and wireless. I tested this standing very close to primary deco and measured speed on phone and laptop on WiFi, also tried plugging in my laptop directly to the primary deco and also wirelessly in other locations in my home. When I disconnected the deco and plugged in my old router, I was getting the expected speeds (over 200mbps).

 

I have already set the total bandwidth in the QoS to 1024, with no high priority devices and set it on standard mode. 

 

I tried changing the ethernet port on the deco that is connected to the modem, and the speeds went up to over 200mbps for maybe 15-20 minutes but when I checked again later, they were back down to below 100mbps.

 

Firmware is updated to the latest version, primary deco is connected directly to ISPs modem and secondary deco is quite close to the primary deco, no walls between them. All my speedtests have been with the speedtest built into the deco app as well as speedtest website/app. 

 

 

  0      
 
  0      
 
#1
Options
14 Reply
Re:Deco M9 plus speed capped at 100mbps on both wired and wireless
2020-07-21 00:34:37 - last edited 2020-07-21 01:01:36

 

As you can see, the deco itself only seems to get about 90mbps from the modem. 

 

But after switching ethernet port on the deco, speed goes up for a little while before coming back down to 90s.

 

  1  
  1  
#2
Options
Re:Deco M9 plus speed capped at 100mbps on both wired and wireless
2020-09-29 08:39:17

@ankur3000 I'm having the exact same issue with Deco M5. Did you manage to resolve it?

  2  
  2  
#3
Options
Re:Deco M9 plus speed capped at 100mbps on both wired and wireless
2020-09-29 09:04:49

@ankur3000 

1. Why Have you set the QOS to 1024, if you internet connections is 250 MBPS then sit it to 250 MBPS Only for its proper functioning.

2. Check the patch cord connecting Modem to your Main Deco, faulty patch cables sometimes do not support 1000 MBPS lan which is essential for speeds above 100 MBPS. 

  2  
  2  
#4
Options
Re:Deco M9 plus speed capped at 100mbps on both wired and wireless
2020-09-29 12:24:32 - last edited 2020-09-29 12:26:16

@Idanbd @jthcomputers 

 

At first I just switched the ethernet port at the back of the Deco M9 and that fixed it, but the same issue would happen again after some time.

 

Later I realized the problem was being caused by me messing with the QOS setting. I just reset everything to factory defaults, set everything else I needed to except the QOS, just don't touch it. Problem hasn't resurfaced since. 

  3  
  3  
#5
Options
Re:Deco M9 plus speed capped at 100mbps on both wired and wireless
2020-10-07 10:20:36

@ankur3000 thanks for the detailed answer.

 

For anyone following, looks like the issue I had was with the network cable, I switched to a different one and it works great ever since.

  1  
  1  
#6
Options
Re:Deco M9 plus speed capped at 100mbps on both wired and wireless
2020-10-09 00:09:30

@Idanbd Switched the cables, changed to Acess Point, and it doesn't get faster than 88 Mbps. crying

  0  
  0  
#7
Options
Re:Deco M9 plus speed capped at 100mbps on both wired and wireless
2020-10-10 11:51:04

@GoncaloLuis Please check whether the router from which you are connecting to deco has a gigabit lan port or not?

  0  
  0  
#8
Options
Re:Deco M9 plus speed capped at 100mbps on both wired and wireless
2020-11-17 08:10:12

@GoncaloLuis Same for me frown

  0  
  0  
#11
Options
Re:Deco M9 plus speed capped at 100mbps on both wired and wireless
2020-11-27 07:18:11

@soulMolecule lease check whether the router from which you are connecting to deco has a gigabit lan port or not. 

verify QoS settings , restore to factory settings and see if it was fixed. 

 

  1  
  1  
#12
Options
Re:Deco M9 plus speed capped at 100mbps on both wired and wireless
2021-07-21 22:53:34

@ankur3000 

I'm having exactly the same problem, I just installed a x60 package with 2 units and it doesn't go over 100mbps and my network is 500mbps, disappointing, I've done all the steps suggested by TP-Link but nothing solves it, I'm on firmware 1.5 .1  .
  1  
  1  
#13
Options
12

Information

Helpful: 0

Views: 9269

Replies: 14

Related Articles
 Speed capped at 100Mbps in one Deco
6598 0
Deco M4 - speed capped at 100Mbps
53065 0
Internet speed capped at 100mbps
2025 0
Deco m9 plus ethernet port max speed
898 0
 Deco m9 plus speed
6400 1
My Deco M4 capped at 100MBPS only
148 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.