MAC address filtering issue on Archer AX73.
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello.
I bought new great wifi router - Archer AX73. But I have an issue with MAC address filtering (white list).
I did a simple test:
- enable MAC address filtering with white list option and add few devices to white list (devices which use wifi and cable),
- restart router, and after restart the only cable devices can connect to my network, all wifi devices are blocked.
The "solution" is: disable MAC address filtering and restart router again, but it is not acceptable solution.
Also adding new MAC address to the existed white list gives no effect. After add new device, restart is required with disabled MAC filtering, and then enable it again.
Kindly want to ask you - do you have similar problems with Archer AX73 router? I believe it is firmware issue, but not sure...
Regards,
Maciej
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I switched language again to Polish (as per tp-link support request) and now everything works fine. I don't know how is it possible...
I asked engineer if he can help you. Will see what will he respond.
- Copy Link
- Report Inappropriate Content
Have you changed the SSID, or left it the same?
I think it's not about the language. I have a few more ideas for experiments, I'll check it later.
I think it's a matter of what and in what order the settings were made.
In any case, it's not okay to look for a single combination of settings and the order in which everything works well.
Unfortunately, the Log is very weak here. It is impossible to understand from it at what stage the error occurs.
There is nothing in it about connecting the client.
For example, here is the log after reboot - wireless clients cannot connect:
2021-02-20 17:14:56 Led Controller INFO [1102] Start to run WAN1_ON
2021-02-20 17:14:56 Led Controller INFO [1102] Start to run WAN0_OFF
2021-02-20 17:14:56 Led Controller INFO [1102] Start to run LAN_ON
2021-02-20 17:14:42 UPnP INFO [11563] Service start
2021-02-20 17:14:41 UPnP INFO [11563] Service stop
2021-02-20 17:14:40 Remote Management INFO [11011] Service stop
2021-02-20 17:14:38 NAT INFO [10438] Initialization succeeded
2021-02-20 17:14:37 NAT INFO [10438] Initialization succeeded
2021-02-20 17:14:35 NAT INFO [8703] IPSEC ALG enabled
2021-02-20 17:14:35 NAT INFO [8703] L2TP ALG enabled
2021-02-20 17:14:35 NAT INFO [8703] PPTP ALG enabled
2021-02-20 17:14:35 NAT INFO [8703] SIP ALG enabled
2021-02-20 17:14:35 NAT INFO [8703] RTSP ALG enabled
2021-02-20 17:14:35 NAT INFO [8703] H323 ALG enabled
2021-02-20 17:14:35 NAT INFO [8703] TFTP ALG enabled
2021-02-20 17:14:35 NAT INFO [8703] FTP ALG enabled
2021-02-20 17:14:33 Led Controller INFO [1102] Start to run NIGHT
2021-02-20 17:14:33 Traffic Statistics INFO [7779] Clear all stats because time changed
2020-09-07 00:00:34 Remote Management INFO [9299] Service stop
2020-09-07 00:00:34 NAT INFO [8703] Initialization succeeded
2020-09-07 00:00:33 Led Controller INFO [1102] Start to run WAN1_OFF
2020-09-07 00:00:33 NAT INFO [8703] Initialization succeeded
2020-09-07 00:00:33 Led Controller INFO [1102] Start to run WAN0_ON
2020-09-07 00:00:33 Led Controller INFO [1102] Start to run LAN_ON
2020-09-07 00:00:32 PPP INFO [8732] ppp receive IPCP ACK
2020-09-07 00:00:32 PPP INFO [8732] ppp send IPCP Req options(addr=176.109.34.106;dns1=109.94.1.21;dns2=109.94.1.18;)
2020-09-07 00:00:32 PPP INFO [8732] ppp receive IPCP NAK options(addr=176.109.34.106;dns1=109.94.1.21;dns2=109.94.1.18;)
2020-09-07 00:00:32 PPP INFO [8732] ppp send IPCP Req options(addr=0.0.0.0;dns1=0.0.0.0;dns2=0.0.0.0;)
2020-09-07 00:00:32 PPP INFO [8732] ppp receive CHAP Success: <null>
2020-09-07 00:00:32 PPP INFO [8732] ppp send CHAP Response name=troshinsn
2020-09-07 00:00:32 PPP INFO [8732] ppp receive CHAP Challenge name=NAS_PPPOE3
2020-09-07 00:00:32 PPP INFO [8732] ppp receive LCP ACK
2020-09-07 00:00:32 PPP INFO [8732] ppp send LCP ACK
2020-09-07 00:00:32 PPP INFO [8732] ppp receive LCP Request options(mru=1492;authtype=PPP_CHAP|type(MD5);magic=0xeaa61b41;)
2020-09-07 00:00:32 PPP INFO [8732] ppp send LCP Request options(mru=1492;magic=0x839d9837;)
2020-09-07 00:00:32 PPP INFO [8732] pppoe receive PADS sess-id(44881)
2020-09-07 00:00:32 PPP INFO [8732] pppoe send PADR Host-Uniq(221c)
2020-09-07 00:00:32 PPP INFO [8732] pppoe receive PADO form AC-MAC(a4:93:4c:37:xx:xx) --------------- (xx from mine!)
2020-09-07 00:00:32 PPP INFO [8732] pppoe receive PADO AC-Name(NAS3)
2020-09-07 00:00:32 PPP INFO [8732] pppoe send PADI Host-Uniq(221c)
2020-09-07 00:00:32 PPP INFO [8732] pppoe send PADT due to(resending PADI)
2020-09-07 00:00:31 Led Controller INFO [1102] Start to run STATUS_ON
2020-09-07 00:00:30 QoS INFO [8426] Service start
2020-09-07 00:00:30 QoS INFO [8426] Function disabled
2020-09-07 00:00:29 Led Controller INFO [1102] Start to run GENERAL
2020-09-07 00:00:27 Traffic Statistics INFO [7776] Service start
2020-09-07 00:00:24 Factory Reset INFO [7304] Service start
2020-09-07 00:00:24 Parental Controls INFO [7149] Service start
2020-09-07 00:00:24 Parental Controls INFO [7149] Function enabled
2020-09-07 00:00:23 Access Control INFO [6128] Service start
2020-09-07 00:00:23 Access Control NOTICE [6128] Flush conntrack table succeeded
2020-09-07 00:00:23 Access Control INFO [6128] Function enabled
2020-09-07 00:00:22 Access Control DEBUG [6128] white list add mac: E8:F4:08:20:xx:xx (xx - from mine.......)
2020-09-07 00:00:22 Access Control DEBUG [6128] white list add mac: 40:45:DA:05:xx:xx
2020-09-07 00:00:22 Access Control DEBUG [6128] white list add mac: 00:11:32:05:xx:xx
2020-09-07 00:00:22 Access Control DEBUG [6128] white list add mac: 90:F6:52:2E:xx:xx
2020-09-07 00:00:22 Access Control DEBUG [6128] white list add mac: 54:E1:AD:33:xx:xx
2020-09-07 00:00:21 Access Control DEBUG [6128] white list add mac: 84:8E:DF:74:xx:xx
2020-09-07 00:00:21 Access Control DEBUG [6128] white list add mac: 34:20:03:33:xx:xx
2020-09-07 00:00:21 Access Control DEBUG [6128] white list add mac: 6C:6A:77:78:xx:xx
2020-09-07 00:00:21 Access Control DEBUG [6128] white list add mac: 00:90:A9:B4:xx:xx
2020-09-07 00:00:19 NAT DEBUG [5417] Flush conntrack
2020-09-07 00:00:19 NAT INFO [5417] Function enabled
2020-09-07 00:00:19 NAT NOTICE [5417] Create NAT chain succeeded
2020-09-07 00:00:18 NAT INFO [5417] Initialization succeeded
2020-09-07 00:00:18 NAT INFO [5417] Initialization succeeded
2020-09-07 00:00:17 Basic Security INFO [4844] Service start
2020-09-07 00:00:17 Basic Security NOTICE [4844] Flush conntrack table succeeded
2020-09-07 00:00:15 Firewall INFO [3071] Service start
2020-09-07 00:00:15 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:15 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:14 IP & MAC Binding INFO [4544] Daemon connection succeeded
2020-09-07 00:00:14 IP & MAC Binding INFO [4544] ARP Binding disabled
2020-09-07 00:00:14 IP & MAC Binding INFO [4544] Config interface initialization succeeded
2020-09-07 00:00:14 IP & MAC Binding INFO [4544] Initialization succeeded
2020-09-07 00:00:14 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:14 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:13 UPnP INFO [4330] Service start
2020-09-07 00:00:13 UPnP INFO [4330] Service stop
2020-09-07 00:00:13 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:13 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:12 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:12 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:11 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:11 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:11 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:11 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:10 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:10 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:09 Remote Management INFO [3530] Service stop
2020-09-07 00:00:09 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:09 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:08 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:08 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:07 Led Controller INFO [1102] Start to run WIFI2G_ON
2020-09-07 00:00:07 Led Controller INFO [1102] Start to run WIFI5G_ON
2020-09-07 00:00:07 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:07 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:07 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:07 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:06 Led Controller ERROR [1102] Config importing failed
2020-09-07 00:00:06 Led Controller DEBUG [1102] Failed to read _ON
2020-09-07 00:00:00 Time Settings INFO [1130] Service start
1970-01-01 00:00:11 Led Controller INFO [1102] Service start
After that I turned off and on again OFDMA.
A minute later, the wireless clients connected. An entry appeared in the log:
2021-02-20 17:18:27 IP & MAC Binding INFO [27441] Daemon connection succeeded
2021-02-20 17:18:27 IP & MAC Binding INFO [27441] ARP Binding disabled
2021-02-20 17:18:27 IP & MAC Binding INFO [27441] Config interface initialization succeeded
2021-02-20 17:18:27 IP & MAC Binding INFO [27441] Initialization succeeded
2021-02-20 17:18:18 Led Controller INFO [1102] Start to run WIFI2G_ON
2021-02-20 17:18:18 Led Controller INFO [1102] Start to run WIFI5G_ON
2021-02-20 17:18:00 IP & MAC Binding INFO [24732] Daemon connection succeeded
2021-02-20 17:18:00 IP & MAC Binding INFO [24732] ARP Binding disabled
2021-02-20 17:18:00 IP & MAC Binding INFO [24732] Config interface initialization succeeded
2021-02-20 17:18:00 IP & MAC Binding INFO [24732] Initialization succeeded
2021-02-20 17:17:51 Led Controller INFO [1102] Start to run WIFI2G_ON
2021-02-20 17:17:51 Led Controller INFO [1102] Start to run WIFI5G_ON
- Copy Link
- Report Inappropriate Content
Never changed SSID, still using the same.
IMO - you are righ, probably any specific sequence in settiong is responsible for this problem. But the question is: which sequence? :)
- Copy Link
- Report Inappropriate Content
Have you changed the number of wireless clients? Maybe it's some kind of client that affects the router?
- Copy Link
- Report Inappropriate Content
No, never changed.
But imo - the simple test should show you if is it a problem. Factory reset with the only simple changes for your internet provider (in eng. lang. of course) and with whitelist for 1-2 wifi devices. Did you try this?
- Copy Link
- Report Inappropriate Content
Yes, I tried it. Hardreset, new SSID, two devices ...
Could you post the router log immediately after it reboots and connects wireless clients? Remove MAC addresses as I did.
- Copy Link
- Report Inappropriate Content
There is my log (anonymized my MAC address list and IP :)), but everything is ok after reboot):
2021-02-23 13:33:09 led-controller[1102]: <6> 288051 Start to run WAN1_ON
2021-02-23 13:33:09 led-controller[1102]: <6> 288051 Start to run WAN0_OFF
2021-02-23 13:33:09 led-controller[1102]: <6> 288051 Start to run LAN_ON
2021-02-23 13:33:07 led-controller[1102]: <6> 288051 Start to run WAN1_ON
2021-02-23 13:33:07 led-controller[1102]: <6> 288051 Start to run WAN0_OFF
2021-02-23 13:33:07 led-controller[1102]: <6> 288051 Start to run LAN_ON
2021-02-23 13:33:06 traffic-stats[7899]: <6> 269001 Clear all stats because time changed
2020-09-07 00:01:27 upnp[14889]: <6> 217504 Service start
2020-09-07 00:01:27 upnp[14889]: <6> 217505 Service stop
2020-09-07 00:01:25 remote-management[14538]: <6> 282505 Service stop
2020-09-07 00:01:17 ddns[13008]: <6> 214001 Dynamic dns noip registered ip: xxx.yyy.zzz.xxx
2020-09-07 00:01:17 ddns[13008]: <5> 214005 Dynamic dns noip login succeed
2020-09-07 00:01:17 ddns[13008]: <6> 214004 Dynamic dns noip return code nochg
2020-09-07 00:01:17 nat[12234]: <6> 211021 IPSEC ALG enabled
2020-09-07 00:01:17 nat[12234]: <6> 211021 L2TP ALG enabled
2020-09-07 00:01:17 nat[12234]: <6> 211021 PPTP ALG enabled
2020-09-07 00:01:17 nat[12234]: <6> 211021 SIP ALG enabled
2020-09-07 00:01:17 nat[12234]: <6> 211021 RTSP ALG enabled
2020-09-07 00:01:17 nat[12234]: <6> 211021 H323 ALG enabled
2020-09-07 00:01:17 nat[12234]: <6> 211021 TFTP ALG enabled
2020-09-07 00:01:17 nat[12234]: <6> 211021 FTP ALG enabled
2020-09-07 00:01:16 nat[12234]: <5> 211054 Virtual server created succeeded[ex-port:2222 ip:192.168.150.170 in-port:22 protocol:all]
2020-09-07 00:01:15 ddns[13008]: <6> 214002 Dynamic dns noip login start
2020-09-07 00:01:14 nat[12234]: <6> 211501 Initialization succeeded
2020-09-07 00:01:13 nat[12234]: <6> 211501 Initialization succeeded
2020-09-07 00:00:34 led-controller[1102]: <6> 288051 Start to run WAN1_OFF
2020-09-07 00:00:34 led-controller[1102]: <6> 288051 Start to run WAN0_ON
2020-09-07 00:00:34 led-controller[1102]: <6> 288051 Start to run LAN_ON
2020-09-07 00:00:32 led-controller[1102]: <6> 288051 Start to run STATUS_ON
2020-09-07 00:00:31 qos[8837]: <6> 259504 Service start
2020-09-07 00:00:31 qos[8837]: <6> 259503 Function disabled
2020-09-07 00:00:31 led-controller[1102]: <6> 288051 Start to run NIGHT
2020-09-07 00:00:31 led-controller[1102]: <6> 288051 Start to run GENERAL
2020-09-07 00:00:28 traffic-stats[7895]: <6> 269504 Service start
2020-09-07 00:00:24 factory-reset[7226]: <6> 284504 Service start
2020-09-07 00:00:23 parental-control[7013]: <6> 229504 Service start
2020-09-07 00:00:23 parental-control[7013]: <6> 229502 Function enabled
2020-09-07 00:00:22 access-control[6002]: <6> 239504 Service start
2020-09-07 00:00:22 access-control[6002]: <5> 239606 Flush conntrack table succeeded
2020-09-07 00:00:22 access-control[6002]: <6> 239502 Function enabled
2020-09-07 00:00:22 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:22 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:22 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:22 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:21 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:20 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:20 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:20 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:20 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:20 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:20 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:20 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:20 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:20 access-control[6002]: <7> 239012 white list add mac: AA:BB:CC:DD:EE:FF
2020-09-07 00:00:18 nat[5036]: <7> 211001 Flush conntrack
2020-09-07 00:00:18 nat[5036]: <6> 211502 Function enabled
2020-09-07 00:00:18 nat[5036]: <5> 211051 Create NAT chain succeeded
2020-09-07 00:00:16 nat[5036]: <6> 211501 Initialization succeeded
2020-09-07 00:00:16 nat[5036]: <6> 211501 Initialization succeeded
2020-09-07 00:00:15 imb[5090]: <6> 218507 Daemon connection succeeded
2020-09-07 00:00:15 imb[5090]: <6> 218012 ARP Binding disabled
2020-09-07 00:00:15 imb[5090]: <6> 218506 Config interface initialization succeeded
2020-09-07 00:00:15 imb[5090]: <6> 218501 Initialization succeeded
2020-09-07 00:00:15 upnp[4879]: <6> 217504 Service start
2020-09-07 00:00:15 basic-security[4477]: <6> 219504 Service start
2020-09-07 00:00:15 basic-security[4477]: <5> 219606 Flush conntrack table succeeded
2020-09-07 00:00:15 upnp[4879]: <6> 217505 Service stop
2020-09-07 00:00:14 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:14 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:13 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:13 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:13 firewall[3304]: <6> 209504 Service start
2020-09-07 00:00:13 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:13 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:12 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:12 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:11 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:11 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:10 remote-management[3840]: <6> 282505 Service stop
2020-09-07 00:00:10 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:10 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:09 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:09 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:08 led-controller[1102]: <6> 288051 Start to run WIFI2G_ON
2020-09-07 00:00:08 led-controller[1102]: <6> 288051 Start to run WIFI5G_ON
2020-09-07 00:00:08 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:08 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:07 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:07 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:07 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:07 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:07 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:07 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:06 led-controller[1102]: <3> 288753 Config importing failed
2020-09-07 00:00:06 led-controller[1102]: <7> 288009 Failed to read _ON
2020-09-07 00:00:00 time-settings[1130]: <6> 279504 Service start
1970-01-01 00:00:11 led-controller[1102]: <6> 288504 Service start
- Copy Link
- Report Inappropriate Content
Thanks!!!!
I compared mine and yours LOGs. There is a difference in the order in which system components are loaded, but I don’t think it is important. I also have PPPOE, and you have DYNDNS. I will try to turn on DYNDNS next time. But I was most interested in the end of the log (Top strings). I see you have lines like this:
2021-02-23 13:33:09 led-controller[1102]: <6> 288051 Start to run WAN1_ON
2021-02-23 13:33:09 led-controller[1102]: <6> 288051 Start to run WAN0_OFF
2021-02-23 13:33:09 led-controller[1102]: <6> 288051 Start to run LAN_ON
2021-02-23 13:33:07 led-controller[1102]: <6> 288051 Start to run WAN1_ON
2021-02-23 13:33:07 led-controller[1102]: <6> 288051 Start to run WAN0_OFF
2021-02-23 13:33:07 led-controller[1102]: <6> 288051 Start to run LAN_ON
As I understand it, they are talking about WiFi initialization. You have it twice. I have it once:
2021-02-20 17:14:56 Led Controller INFO [1102] Start to run WAN1_ON
2021-02-20 17:14:56 Led Controller INFO [1102] Start to run WAN0_OFF
2021-02-20 17:14:56 Led Controller INFO [1102] Start to run LAN_ON
I think the problem is somewhere here ... Because if I manually re-initialize WiFi (for example, turn off and turn on WiFi using the button on the router), then the clients are immediately connected. The question is - why do you have two initializations, and I have one?
Can you look at the log again? Without doing any manipulation of the router settings after rebooting. Do you always have these 3 lines twice after a reboot?
- Copy Link
- Report Inappropriate Content
I can check this (log after next reboot) during next week. Actually I am out of home. But you are probably right - twice wifi initialization during reboot may be solution, but I don't have idea how to obtain this.
As per support talk me, they are preparing beta firmware for us. So, will see what will happened after upgrade...
- Copy Link
- Report Inappropriate Content
thanks, I will be very grateful!
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 7864
Replies: 44
Voters 0
No one has voted for it yet.