Home

Forums

Stories

Knowledge Base

Home Network Community > Wi-Fi Routers > Link aggregation on AX 11000 router

< Wi-Fi Routers

Link aggregation on AX 11000 router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Link aggregation on AX 11000 router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

davegray

2021-02-15 10:49:12 - last edited 2021-02-17 07:07:14

Posts: 8

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-02-15

Link aggregation on AX 11000 router

2021-02-15 10:49:12 - last edited 2021-02-17 07:07:14

Model: Archer AX11000

Hardware Version:

Firmware Version:

Hello

Just bought a new AX 11000 router and I would like to setup "link aggregation". The LAN page on the router portal

shows I can enable this and the LAN2 and LAN3 are combined, questions is which port do I plug my ethernet cable in to?

Or does it not matter?

Thanks

Dave

1 Accepted Solution

MagiX

LV1

2021-02-16 10:08:32 - last edited 2021-02-17 07:07:14

Posts: 8

Helpful: 4

Solutions: 1

Stories: 0

Registered: 2021-02-08

Re:Link aggregation on AX 11000 router-Solution

2021-02-16 10:08:32 - last edited 2021-02-17 07:07:14

@davegray

Well, the point is that you can not connect everything through link aggregation.

You cannot connect TVs, PS4s or most of the laptops... this type of connection is used usually for NAS storage systems or similar.

For link aggregation you need to connect both cables to both devices (Router and NAS) and both need to support this type of link aggregation connection.

Recommended Solution

8 Reply

MagiX

LV1

2021-02-15 12:55:41 - last edited 2021-02-15 14:13:33

Posts: 8

Helpful: 4

Solutions: 1

Stories: 0

Registered: 2021-02-08

Re:Link aggregation on AX 11000 router

2021-02-15 12:55:41 - last edited 2021-02-15 14:13:33

@davegray

WAN - For internet connection

LAN 1 and LAN2 - both from an additional device for that you want to have a higher connection speed

terziyski

LV7

2021-02-15 13:44:56

Posts: 7017

Helpful: 5224

Solutions: 1159

Stories: 7

Registered: 2013-10-12

Re:Link aggregation on AX 11000 router

2021-02-15 13:44:56

@davegray

According to your screenshot and to your device manual 12.2.3 you have to plug the cables in ports LAN2 & LAN3 on the router side.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

davegray

LV1

2021-02-16 08:21:22

Posts: 8

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-02-15

Re:Link aggregation on AX 11000 router

2021-02-16 08:21:22

MagiX wrote

@davegray

WAN - For internet connection

LAN 1 and LAN2 - both from an additional device for that you want to have a higher connection speed

@MagiX I know both LAN ports are joined internally to the router but I asked which of the two LAN2 or LAN3 do I connect to the eithernet port on my device, I cannot connect 2 into 1 .

davegray

LV1

2021-02-16 08:22:40

Posts: 8

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-02-15

Re:Link aggregation on AX 11000 router

2021-02-16 08:22:40

How do two ports LAN2 and LAN3 go into one device (laptop, xbox etc)?

MagiX

LV1

2021-02-16 10:08:32 - last edited 2021-02-17 07:07:14

Posts: 8

Helpful: 4

Solutions: 1

Stories: 0

Registered: 2021-02-08

Re:Link aggregation on AX 11000 router-Solution

2021-02-16 10:08:32 - last edited 2021-02-17 07:07:14

@davegray

Well, the point is that you can not connect everything through link aggregation.

You cannot connect TVs, PS4s or most of the laptops... this type of connection is used usually for NAS storage systems or similar.

For link aggregation you need to connect both cables to both devices (Router and NAS) and both need to support this type of link aggregation connection.

Recommended Solution

davegray

LV1

2021-02-16 12:48:29

Posts: 8

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-02-15

Re:Link aggregation on AX 11000 router

2021-02-16 12:48:29

Ah right I see. The receiving device needs two ethernet ports? I thought it was a 2 into 1 type of setup. Regards

terziyski

LV7

2021-02-16 17:07:09

Posts: 7017

Helpful: 5224

Solutions: 1159

Stories: 7

Registered: 2013-10-12

Re:Link aggregation on AX 11000 router

2021-02-16 17:07:09

@davegray

You can read this gude for more details.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

Tom1953

LV1

2021-12-16 06:15:18

Posts: 1

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2021-12-16

Re:Link aggregation on AX 11000 router

2021-12-16 06:15:18

Thank you. They don't use F0, F1, F2, and counting and not counting the WAN port is obnoxious. I have not confirmed yet, but on a Synology NAS, the recommendation is to switch the Link Aggregation mode on the NAS from "Adaptive Load Balancing" to "Balance XOR."

Link aggregation on AX 11000 router

Link aggregation on AX 11000 router

Information

Voters 0

Tags