Home

Forums

Stories

Knowledge Base

Business Community > Routers > Failed to update firmware via Omada - WARNING it downloads wrong firmware

< Routers

Failed to update firmware via Omada - WARNING it downloads wrong firmware

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Failed to update firmware via Omada - WARNING it downloads wrong firmware

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

mavicPL

2021-06-03 14:37:07 - last edited 2021-06-04 10:11:45

Posts: 3

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-06-03

Failed to update firmware via Omada - WARNING it downloads wrong firmware

2021-06-03 14:37:07 - last edited 2021-06-04 10:11:45

Model: ER7206 (TL-ER7206)

Hardware Version: V1

Firmware Version: 1.0.1

I tried to update today firmware via Omada Controller 4.3.5 - id showed up I can update from 1.0.1 to 1.1.0. After update it cannot adopt. I got message firmware is newer than omada.

I reset router to factory defaults. After logging it has firmware version 1.0.0 Build.20151228 Rel.82868 and it shows as WVR450G device. Omada downloaded wrong firmware!

Ca I do sth or its just a brick?

1 Accepted Solution

Fae

2021-06-04 06:52:19 - last edited 2021-06-04 10:11:45

Posts: 3613

Helpful: 1358

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:Failed to update firmware via Omada - WARNING it downloads wrong firmware-Solution

2021-06-04 06:52:19 - last edited 2021-06-04 10:11:45

Dear @mavicPL,

mavicPL wrote

I'm using Omada Software Controller v4.3.5 (Windows). Sys Led is blinking. I can logon into web UI but router shows up as WVR450G model. Look at attached screenshots.

Thank you for the detailed information. Could you please refer to the guide below and check if it helps?

How to use the Emergency Mode to recovery the firmware for Omada Gateways

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Recommended Solution

4 Reply

Fae

2021-06-04 01:42:53 - last edited 2021-06-04 01:55:33

Posts: 3613

Helpful: 1358

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:Failed to update firmware via Omada - WARNING it downloads wrong firmware

2021-06-04 01:42:53 - last edited 2021-06-04 01:55:33

Dear @mavicPL,

mavicPL wrote

I tried to update today firmware via Omada Controller 4.3.5 - id showed up I can update from 1.0.1 to 1.1.0. After update it cannot adopt. I got message firmware is newer than omada. I reset router to factory defaults. After logging it has firmware version 1.0.0 Build.20151228 Rel.82868 and it shows as WVR450G device. Omada downloaded wrong firmware!

Are you using Omada Software Controller or Omada Hardware Controller (OC200/OC300)?

Did you access the Omada Controller via cloud website(https://omada.tplinkcloud.com/) when you try to update the firmware?

What's the LED status on the router now? Is the SYS LED blinking or completely off?

Is there any other device connected to the ER7206 when you log into the web UI of the ER7206 router?

Please disconnect other cables and simply plug one PC into the LAN port before you log into the web UI for checking.

If you doubt it is bricked, please check if the FAQ below could help:

How to use the Emergency Mode to recovery the firmware for Omada Gateways

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

mavicPL

LV1

2021-06-04 06:12:46

Posts: 3

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-06-03

Re:Failed to update firmware via Omada - WARNING it downloads wrong firmware

2021-06-04 06:12:46

@Fae

I'm using Omada Software Controller v4.3.5 (Windows). Sys Led is blinking. I can logon into web UI but router shows up as WVR450G model.

Look at attached screenshots.

File:

firmware1.jpgDownload

Fae

2021-06-04 06:52:19 - last edited 2021-06-04 10:11:45

Posts: 3613

Helpful: 1358

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:Failed to update firmware via Omada - WARNING it downloads wrong firmware-Solution

2021-06-04 06:52:19 - last edited 2021-06-04 10:11:45

Dear @mavicPL,

mavicPL wrote

I'm using Omada Software Controller v4.3.5 (Windows). Sys Led is blinking. I can logon into web UI but router shows up as WVR450G model. Look at attached screenshots.

Thank you for the detailed information. Could you please refer to the guide below and check if it helps?

How to use the Emergency Mode to recovery the firmware for Omada Gateways

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Failed to update firmware via Omada - WARNING it downloads wrong firmware

Failed to update firmware via Omada - WARNING it downloads wrong firmware

Information

Voters 0

Tags