Home Network Community > Access Points > Point to Point with LAN Each end
< Access Points

Point to Point with LAN Each end

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Point to Point with LAN Each end

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Point to Point with LAN Each end
Point to Point with LAN Each end
2013-07-04 16:36:48
Region : New Zealand

Model : TL-WA7510N

Hardware Version :

Firmware Version :

ISP :

I am trying to link two LAN's in router mode. For various reasons I do NOT want to use bridge mode.
My LAN's are 192.168.1.0/24 and 192.168.2.0/24
I am using 10.10.10.1/30 and 10.10.10.2/30 as the WAN's
I have routes for 192.168.2.0 via 10.10.10.1 and 192.168.1.0 via 10.10.10.2
The problem I have is what other settings I need ? I have both in AP Client Router Mode
The radios do not seem to see each other which suggests they are not transmitting.
Any suggestions please ?
File:
TPRouters.jpgDownload
  0      
 
  0      
 
#1
Options
5 Reply
Re:Point to Point with LAN Each end
2013-07-04 21:17:33
to start I have both in AP Client Router Mode I asume by picture and your other post its a 7510
in OPERATION MODE both have to be Standard AP
Wireless/Wireless Settings/Operation Mode/one as AP and the other as CLIENT, as you can see its messy, the command repeats, but i am not the manufacturer.
about your LAN's and WAN's are a mess
File:
  0  
  0  
#2
Options
Re:Point to Point with LAN Each end
2013-07-06 08:59:17
If I am running Access Point and Client it's not really a point to point links is it ? It's more a multi point service. I want a tightly controlled network between two LAN's. Only possible connections are the other end and data routed from one LAN to the other but only from the roted devices. I know I have shown whole network routed in my diagram.
  0  
  0  
#3
Options
Re:Point to Point with LAN Each end
2013-07-07 01:53:40

Radata wrote

If I am running Access Point and Client it's not really a point to point links is it ? It's more a multi point service. I want a tightly controlled network between two LAN's. Only possible connections are the other end and data routed from one LAN to the other but only from the roted devices. I know I have shown whole network routed in my diagram.

I know I have shown whole network routed in my diagram your diagram only shows 2 radios so its a PTP if you add one or more radios, then would be a PtMP
about Only possible connections are the other end and data routed from one LAN to the other but only from the roted devices. remember my answer on post #2 about your LAN's and WAN's are a mess
  0  
  0  
#4
Options
Re:Point to Point with LAN Each end
2013-07-07 09:44:58
"about your LAN's and WAN's are a mess" Actually this is the way many commercial radio modems would do it. The WAN is 10.10.10.x and the LAN's are 192.168.xxx.xxx That's normal...
  0  
  0  
#5
Options
Re:Point to Point with LAN Each end
2013-07-07 20:48:16

Radata wrote

"about your LAN's and WAN's are a mess" Actually this is the way many commercial radio modems would do it. The WAN is 10.10.10.x and the LAN's are 192.168.xxx.xxx That's normal...

Good Luck
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 627

Replies: 5

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.