Software Controller_V5.9.9_Linux to oc200 somehow ??

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Software Controller_V5.9.9_Linux to oc200 somehow ??

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Software Controller_V5.9.9_Linux to oc200 somehow ??
Software Controller_V5.9.9_Linux to oc200 somehow ??
2023-05-30 13:03:33 - last edited 2023-06-05 02:02:59

is there a way to move my current configuration from linux to an oc200 somehow ?? 

i would like to add the oc200, and get the controller off my nas.. 

 

thanks 

  0      
  0      
#1
Options
2 Accepted Solutions
Re:Software Controller_V5.9.9_Linux to oc200 somehow ?? -Solution
2023-05-31 07:35:25 - last edited 2023-06-05 02:02:59

Hello @JS_racer

 

You may refer to this FAQ to try the migration feature.

Please make sure the firmware version between Linux software controller and OC200 is the same.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
Re:Software Controller_V5.9.9_Linux to oc200 somehow ?? -Solution
2023-06-02 17:49:07 - last edited 2023-06-05 02:03:01

well, got the oc200 today. updated the firmware migrated the controller, followed the process. worked great i think.. lol 

very easy to follow, process went great... always a tic puckering, but no issues i know of. 

 

thanks much for all the help guys, very much appriciated. 

had a small old thumb drive, so installed that as well for auto backups. 

 

my nas running docker and omada was crazy with activity every few seconds.. hope the oc200 does well... 

Recommended Solution
  0  
  0  
#6
Options
5 Reply
Re:Software Controller_V5.9.9_Linux to oc200 somehow ?? -Solution
2023-05-31 07:35:25 - last edited 2023-06-05 02:02:59

Hello @JS_racer

 

You may refer to this FAQ to try the migration feature.

Please make sure the firmware version between Linux software controller and OC200 is the same.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#2
Options
Re:Software Controller_V5.9.9_Linux to oc200 somehow ??
2023-05-31 11:49:17 - last edited 2023-05-31 13:26:31

  @Hank21 

"Please make sure the firmware version between Linux software controller and OC200 is the same."

 

seeing 5.9.32 for the oc200, 5.9.9 lunix 

is 5.9 close enough ?? 

 

is site migration or controller migration used if there is only one site on the controller ?? (just my home network) 

  0  
  0  
#3
Options
Re:Software Controller_V5.9.9_Linux to oc200 somehow ??
2023-06-02 01:14:27

  @JS_racer 

 

As I know, it will be OK only if the primary version is the same like the V5.9.X.

Just striving to develop myself while helping others.
  2  
  2  
#4
Options
Re:Software Controller_V5.9.9_Linux to oc200 somehow ??
2023-06-02 07:17:35

 With the OC200, it is better to migrate each site, 1 at a time, to the new controller, rather than an entire controller backup

 

<< Paying it forward, one juicy problem at a time... >>
  2  
  2  
#5
Options
Re:Software Controller_V5.9.9_Linux to oc200 somehow ?? -Solution
2023-06-02 17:49:07 - last edited 2023-06-05 02:03:01

well, got the oc200 today. updated the firmware migrated the controller, followed the process. worked great i think.. lol 

very easy to follow, process went great... always a tic puckering, but no issues i know of. 

 

thanks much for all the help guys, very much appriciated. 

had a small old thumb drive, so installed that as well for auto backups. 

 

my nas running docker and omada was crazy with activity every few seconds.. hope the oc200 does well... 

Recommended Solution
  0  
  0  
#6
Options