Archer AX55 2.4ghz Problem Again...
Archer AX55 2.4ghz Problem Again...
Hi,
Just bought this Ax55 router yesterday. I have set up and configuring it manually to meet my network requirements and suprisingly noted that 2.4ghz band is not working.
Updated to the latest official firmware but not fixed at all. I have tried all downgraded firmware which is possible.
The exact problem is 2.4Ghz SSID is not visible when I search available network on iPhone 13 Pro or my Sonos Beam Gen2 or Dell Latitude laptop or iPad Air 5gen.
I have turned off Smart Connect, EasyMesh, used different names for the 2.4 and 5ghz band, manually tried Band 6,3,11 without success.
Also tried every settings in wireless options without success. Some short periods after reboot the SSID shows up but every device says unable to connect if I enter correct password.
I also tried with different security like WPA2, WPA3 or mixed personal but no success.
2.4ghz Guest network and Iot also not working. Cannot connect my 2.4ghz Xiaomi Security Camera and my Sonos Beam Gen2 Soundbar which are using only 2.4ghz
I'm using these in a flat with 3-4meters distance from the router.
My solution is I'm using now a 2nd router for 2.4ghz (Linksys MR7350V1) in bridge mode but I really angry about I have bought a relative expensive TP-Link and it is half useless!! This is crazy by the way. Even DD-WRT firmware is not available to test this issue. And this is a 1day old router!!
Now I need to use 2 different router to meet my requirements which is crazy! Also I don't know why are the built in USB port don't support printer server function in this catergory of routers. I can't share my printer in the network...
Please reply back with some real solution because many topics are dealing with this problem but there are no real solutions except change bands or reset or something useless steps. These are not working at all!!
Thanks
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Slayer86 wrote
No! Unfortunately I was not solved it. I'm using two routers at the same time to use both bands :D lol
Really crazy. I have turned off the 2.4ghz on the Archer and use a Linksys router for 2.4ghz only :)
Hi, did you replace the AX55 router with the seller? or it has the same issue with the replacement?
- Copy Link
- Report Inappropriate Content
Fortunately reseting of the router solved the problem. It was working ok some time ago, then the 2.4G frequency started to disappear. Now everything is working. The only inconvinience is the repeated setup. Next time I will save my settings before doing a factory reset. :)
- Copy Link
- Report Inappropriate Content
@Fsanya Hello, happy to know that you have resolved the problem by resetting the router, thanks a lot for the update.
@Slayer86 If the same issue still exists on your router now, please try factory reset it again, and you could save the current configuration file before the factory reset to avoid reconfiguration especially when you have configured some advanced functions.
- Copy Link
- Report Inappropriate Content
@Slayer86 I have the exact same issue. In my case everything was working perfectly for a few months until I updated the firmware to "1.2.2 Build 20230803 rel.35127(5553)". Then this exact same problem as you describe started. I haven't tried to downgrade the firmware yet but I'm also convinced it's not a hardware issue.
Slayer86 wrote
No! Unfortunately I was not solved it. I'm using two routers at the same time to use both bands :D lol
Really crazy. I have turned off the 2.4ghz on the Archer and use a Linksys router for 2.4ghz only :)
- Copy Link
- Report Inappropriate Content
Hi, as Slayer86 mentioned, the issue is resolved after a factory reset, so please try factory reset your router as well.
It is recommended to save the current configuration file before the factory reset to avoid reconfiguration especially when you have configured some advanced functions.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 3474
Replies: 15
Voters 0
No one has voted for it yet.