Home

Forums

Stories

Knowledge Base

Home Network Community > Wi-Fi Routers > MU-MIMO can't be enabled on BE800

< Wi-Fi Routers

MU-MIMO can't be enabled on BE800

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

MU-MIMO can't be enabled on BE800

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

MU-MIMO can't be enabled on BE800

2024-05-02 05:44:32 - last edited 2024-06-05 01:22:11

Posts: 12

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2023-08-27

MU-MIMO can't be enabled on BE800

2024-05-02 05:44:32 - last edited 2024-06-05 01:22:11

Model: Archer BE800

Hardware Version: V1

Firmware Version: 1.1.1

I've upgraded my BE800 to FQ v1.1.1 a while which don't have a problem.

However, when I check my BE800 & RE815XE today for any setting can be fine tuned, then I found MU-MIMO cannot be used. If I'm not wrong, I used it when my BE800 was FW v1.0.12 & FW v1.0.9 (when I first installed to use it). I've tried again to set to use "OFDMA+MU-MIMO" but it only set to "OFDMA only". I tried to downgrade the firmware to v1.0.12 & v1.0.9 to verify if this is a bug by v1.1.1, but the downgrade process failed which should be due to v1.1.x can't be reverted to v1.0.x.

Any advise how I can use MU-MIMO on BE800 v1.1.1? Please note I still can use OFDMA+MU-MIMO on RE815XE. I'm use MESH.

Archer BE800 v1_v1.1.5 RE815XE v1_1.0.6 RE705X v1_1.0.10

0

0

#1

4 Reply

LV7

2024-05-02 10:32:40 - last edited 2024-06-05 01:22:11

Posts: 7008

Helpful: 5217

Solutions: 1157

Stories: 7

Registered: 2013-10-12

Re:MU-MIMO can't be enabled on BE800

2024-05-02 10:32:40 - last edited 2024-06-05 01:22:11

You can try the FW release from this post for the MU-MIMO issue on BE800 v1.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

1

1

#2

LV1

2024-05-03 06:08:29

Posts: 12

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2023-08-27

Re:MU-MIMO can't be enabled on BE800

2024-05-03 06:08:29

Thank you. I downloaded and using the v1.1.1 beta. Now The MU-MIMO can be enabled, but the wallpaper of GUI now showing BETA

Archer BE800 v1_v1.1.5 RE815XE v1_1.0.6 RE705X v1_1.0.10

0

0

#3

LV7

2024-05-03 08:28:48

Posts: 7008

Helpful: 5217

Solutions: 1157

Stories: 7

Registered: 2013-10-12

Re:MU-MIMO can't be enabled on BE800

2024-05-03 08:28:48

That's normal - it's beta FW version aiming to fix the MU-MIMO issue. When the next stable FW comes these watermarks would be gone.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

0

0

#4

LV1

2024-05-04 17:20:24

Posts: 5

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2024-05-04

Re:MU-MIMO can't be enabled on BE800

2024-05-04 17:20:24

@terziyski is anyone getting constant crashing with both the 1.1.1 and the 1.99.97 beta build? My router crashes and restarts at least twice a day.

0

0

#5