Home Network Community > Wi-Fi Routers > Archer AX73 Ethernet Status - LAN2 seems to be capped / LAN4 is disabled
< Wi-Fi Routers

Archer AX73 Ethernet Status - LAN2 seems to be capped / LAN4 is disabled

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer AX73 Ethernet Status - LAN2 seems to be capped / LAN4 is disabled

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer AX73 Ethernet Status - LAN2 seems to be capped / LAN4 is disabled
Archer AX73 Ethernet Status - LAN2 seems to be capped / LAN4 is disabled
2024-11-10 08:31:14 - last edited 2024-11-27 11:50:00
Model: Archer AX73  
Hardware Version: V1
Firmware Version: 1.3.6 Build 20240325 rel.39241(5553)

Hi, my Archer AX73, I detected this problems after several years of using.

 

LAN2 speed seems to be capped and LAN4 is disabled.

 

In my opinion, it's likely a hardware issue or Can I just configure some settings to solve it ?

 

 

Thank you for advices.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Archer AX73 Ethernet Status - LAN2 seems to be capped / LAN4 is disabled-Solution
2024-11-10 15:39:26 - last edited 2024-11-27 11:50:00

  @ArnanC 

 

In that case it's probably a HW issue and you probably should contact your local support for help.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
Recommended Solution
  0  
  0  
#4
Options
3 Reply
Re:Archer AX73 Ethernet Status - LAN2 seems to be capped / LAN4 is disabled
2024-11-10 14:38:29

  @ArnanC 

 

If you don't have anything plugged in LAN 4 its status would be like in your screenshot.

In LAN 2 you probably have plugged a device which can't sync on 1000mbps bandwidth.

Plug that device in LAN 4 port and check the negotiated speed. If it's the same change the ethernet cable and test again.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:Archer AX73 Ethernet Status - LAN2 seems to be capped / LAN4 is disabled
2024-11-10 15:27:52

  @terziyski I did it, unfortunately, for LAN4, anything is not function

For LAN2, I switched LAN1 which is 1000Mbps, at LAN2 its speed decreased to 100Mbps.

Therefore, I think it apparently is the issue of hardware.

  0  
  0  
#3
Options
Re:Archer AX73 Ethernet Status - LAN2 seems to be capped / LAN4 is disabled-Solution
2024-11-10 15:39:26 - last edited 2024-11-27 11:50:00

  @ArnanC 

 

In that case it's probably a HW issue and you probably should contact your local support for help.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
Recommended Solution
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 420

Replies: 3

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.