Model :

Hardware Version : Not Clear

Firmware Version :

ISP :

Hi *

Couple days ago I got new TP-Link Archer T4U ver.1.0 and have installed it on Windows 10. According documentation:
http://www.tp-link.com/resources/document/Archer_T4U_V1_Datasheet.pdf
http://www.tp-link.com/res/down/doc/Archer_T4U(UN)_V1_UG.pdf (Ch.3.3.4 p.14)

This Wi-Fi adapter has option ad-hoc wireless mode (Software Access Point). However, in utility this option is grayed, so I cannot click it.

In addition I tried to enable SoftAP via command prompt:

[CODE]C:\WINDOWS\system32>netsh wlan set hostednetwork mode=allow ssid=WiFi-AP key=Pa77w0rd
The hosted network mode has been set to allow.
The SSID of the hosted network has been successfully changed.
The user key passphrase of the hosted network has been successfully changed.




C:\WINDOWS\system32>netsh wlan start hostednetwork
The hosted network couldn't be started.
The group or resource is not in the correct state to perform the requested operation.






C:\WINDOWS\system32>
[/CODE]

I did small research and found this:

[CODE]C:\WINDOWS\system32>netsh wlan show drivers


Interface name: WiFi 2


Driver : TP-LINK Wireless USB Adapter
Vendor : TP-LINK TECHNOLOGIES CO., LTD.
Provider : TP-LINK TECHNOLOGIES CO., LTD.
Date : 29-10-2015
Version : 1030.2.731.2015
INF file : C:\WINDOWS\INF\oem41.inf
Files : 3 total
C:\WINDOWS\system32\DRIVERS\rtwlanu.sys
C:\WINDOWS\system32\DRIVERS\TP_PHY_REG_PG_Enc.txt
C:\WINDOWS\system32\DRIVERS\TP_TXPWR_LMT_Enc.txt
Type : Native Wi-Fi Driver
Radio types supported : 802.11n 802.11g 802.11b 802.11n 802.11a
FIPS 140-2 mode supported : Yes
802.11w Management Frame Protection supported : Yes
Hosted network supported : No
Authentication and cipher supported in infrastructure mode:
Open None
WPA2-Personal CCMP
Open WEP-40bit
Open WEP-104bit
Open WEP
WPA-Enterprise TKIP
WPA-Personal TKIP
WPA2-Enterprise TKIP
WPA2-Personal TKIP
WPA-Enterprise CCMP
WPA-Personal CCMP
WPA2-Enterprise CCMP
Vendor defined TKIP
Vendor defined CCMP
Vendor defined Vendor defined
Vendor defined Vendor defined
WPA2-Enterprise Vendor defined
WPA2-Enterprise Vendor defined
Vendor defined Vendor defined
Vendor defined Vendor defined
IHV service present : Yes
IHV adapter OUI : [00 e0 4c], type: [00]
IHV extensibility DLL path: C:\WINDOWS\system32\Rtlihvs.dll
IHV UI extensibility ClSID: {6c2a8cca-b2a2-4d81-a3b2-4e15f445c312}
IHV diagnostics CLSID : {00000000-0000-0000-0000-000000000000}
Wireless Display Supported: No (Graphics Driver: No, Wi-Fi Driver: Yes)




C:\WINDOWS\system32>
[/CODE]

As you may notice that a

Hosted network supported : No

How can I enable it?

P.S. As I see adapter uses Realtek RTL8812AU which has a linux driver on github, but also without AP mode.
https://wikidevi.com/wiki/TP-LINK_Archer_T4U
https://github.com/ulli-kroll/rtl8821au