Home Network Community > Wi-Fi Routers > Archer AC1200 not working - only WPS light on
< Wi-Fi Routers

Archer AC1200 not working - only WPS light on

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Archer AC1200 not working - only WPS light on

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer AC1200 not working - only WPS light on
Archer AC1200 not working - only WPS light on
2017-02-08 09:14:28
Model :

Hardware Version :

Firmware Version :

ISP :

Hi I hope someone can help me. Switched off my wireless router for the night and then switched it on again this morning. Only the WPS light is on and its a solid yellow. The other lights do not go on. Can't see the router on my network.
Soft reset by the WPS/reset button failed.
Hard reset with a small pin into the reset hole failed.
Any suggestions?

Thanks.
  0      
 
  0      
 
#1
Options
15 Reply
Re:Archer AC1200 not working - only WPS light on
2017-02-08 14:26:31

confused wrote

Model :

Hardware Version :

Firmware Version :

ISP :

Hi I hope someone can help me. Switched off my wireless router for the night and then switched it on again this morning. Only the WPS light is on and its a solid yellow. The other lights do not go on. Can't see the router on my network.
Soft reset by the WPS/reset button failed.
Hard reset with a small pin into the reset hole failed.
Any suggestions?

Thanks.


How do you hardware reset?
You need to press and hold the reset button (in the hole) for about 5 seconds to reset the router.

In addition, please try to set up a static IP address on your computer 192.168.0.100/255.255.255.0, and then connect the computer wired to the LAN port of C1200, open a command box and ping 192.168.0.1. Check if you can get a reply from 192.168.0.1. (if the LAN IP address is 192.168.0.1 by default, however, if you have changed it to 192.168.1.1 or other, you need to set up static IP in the same subnet of the LAN IP address of the router.)
  0  
  0  
#2
Options
Re:Archer AC1200 not working - only WPS light on
2017-02-08 19:00:17

tplink wrote

How do you hardware reset?
You need to press and hold the reset button (in the hole) for about 5 seconds to reset the router.

Tried it before but i did it again. Nope. Doesn't work.

In addition, please try to set up a static IP address on your computer 192.168.0.100/255.255.255.0, and then connect the computer wired to the LAN port of C1200, open a command box and ping 192.168.0.1. Check if you can get a reply from 192.168.0.1. (if the LAN IP address is 192.168.0.1 by default, however, if you have changed it to 192.168.1.1 or other, you need to set up static IP in the same subnet of the LAN IP address of the router.)


Managed to ping successfully.
C:\Users\user>ping 192.168.0.1

Pinging 192.168.0.1 with 32 bytes of data:
Reply from 192.168.0.1: bytes=32 time<1ms TTL=100
Reply from 192.168.0.1: bytes=32 time<1ms TTL=100
Reply from 192.168.0.1: bytes=32 time<1ms TTL=100
Reply from 192.168.0.1: bytes=32 time<1ms TTL=100

Ping statistics for 192.168.0.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
  0  
  0  
#3
Options
Re:Archer AC1200 not working - only WPS light on
2017-02-08 19:29:45
So I connected to 192.168.0.1 on my web browser and got a "boot" page. System error. The router cannot start up normally. Please upgrade your router.
I tried to use the two firmware versions from the tp-link website (mine is Archer C1200(EU) Ver 1.0 with the 3 antennas. But it failed at 40%.
Tried going to the UK website and using the VR400 firmware since the wireless looks exactly the same but it failed too...

It goes up about 5.8% then fails at 40%.
Screenshot attached




And yes, I did check for the proper firmware for my model, based on the sticker on the bottom of my device.
  0  
  0  
#4
Options
Re:Archer AC1200 not working - only WPS light on
2017-02-08 20:37:27
Tried again, this time disabling all internet access from my PC. The firmware progress bar goes slowly to 40% then fails with a "Firmware upgrade failed" message.

Time to RMA?
  0  
  0  
#5
Options
Re:Archer AC1200 not working - only WPS light on
2017-02-09 14:23:26

confused wrote

Tried again, this time disabling all internet access from my PC. The firmware progress bar goes slowly to 40% then fails with a "Firmware upgrade failed" message.

Time to RMA?


Please check the hardware version at first which is printed on the label at the back of the router.
In addition, have you extracted the zip file when trying to restore the firmware?
  0  
  0  
#6
Options
Re:Archer AC1200 not working - only WPS light on
2017-10-30 21:19:21
I have exectly the same issue with C9 V3. (CZ version). Only WPS is lit, and simple update page loads from http://192.168.0.1
Update fails at 40% with every .bin available at support site.

Buttons are blocked, so I can't reset, Telnet, or enter recovery mode that opens tftp client on 192.168.0.86. (Did not try if serial connection works.)
I can provide serial number of the device if factory provided firmware is needed to restore.
  0  
  0  
#7
Options
Re:Archer AC1200 not working - only WPS light on
2017-10-31 14:29:40
What is the version of your C9？
You may try to do firmware recovery in the way below: http://forum.tp-link.com/showthread.php?81462-How-to-recovery-the-router-when-you-bricked-it&highlight=fitz
Contact support@tp-link.com if this can't help.
  0  
  0  
#8
Options
Re:Archer AC1200 not working - only WPS light on
2017-12-10 03:40:38
Hi,

Did this problem get resolved? I've got exactly the same problem, it's TP-Link Archer C9 V3 (US). The router was working normally, till the moment I plugged it into WAN. My guess is that it tried to auto-update itself and it went wrong. Anyway, I ended up with semi-bricked router, only WPS LED is on. When I upload new firmware file through web (192.168.0.1) I get the same message: "Upgrade failed. The computer is disconnected from the network". I'm able to make it pick up recovery file via TFTP as well, but still no luck either.

Any clues?

Thanks
  0  
  0  
#9
Options
Re:Archer AC1200 not working - only WPS light on
2017-12-10 23:23:21
buenos dias compre un router archer c 50 ac 1200 y no se como configurarlo si alguien me podría ayudar muchas gracias.
  0  
  0  
#10
Options
Re:Archer AC1200 not working - only WPS light on
2017-12-23 10:32:53
I'm having exactly the same problem for my Archer C1200.
Can anyone please advise? thanks.
  0  
  0  
#11
Options
12

Information

Helpful: 0

Views: 7674

Replies: 15

Related Articles
Archer AC1200 Not working via ethernet
771 0
 Archer C9 v4 only WPS LED light
1604 0
Archer A5 not working only power light on
695 0
Archer A6 (AC1200) not working after firmware upgrade !!
3368 3
 client WPS setup for RE305 (AC1200)
1207 0
ac1200 to archer mr200
861 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.