Home Network Community > All Threads > No Access Point option in Archer C1200 V2
< All Threads

No Access Point option in Archer C1200 V2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

No Access Point option in Archer C1200 V2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
No Access Point option in Archer C1200 V2
No Access Point option in Archer C1200 V2
2017-12-29 17:59:10
Model :

Hardware Version :

Firmware Version :

ISP :

Hardware version: Archer C1200 v2.0
Firmware version: 2.0.0 Build 20170206 rel.46023 (EU)

In the website of http://www.tp-link.com/us/download/Archer-C1200_V2.html there is a video link about "how to turn router into an access point", but the video shows an option called "operation mode", but my TP-Link Archer C1200 V2 hasn't this option.

I have got my TPLink Archer C1200 with DHCP disabled works like a Access Point, using only wifi and switch ports and configuring the LAN ip address with an ip address from my local network.

The problem is there is a local network connection but no internet connection because there is no option to setup a gateway for the local network. I suppose that in "access point" mode it will be possible, but no with my current firmware.

what can I do? there is no other firmware version?

Thanks in advance.
  0      
 
  0      
 
#1
Options
13 Reply
Re:No Access Point option in Archer C1200 V2
2017-12-30 04:09:07
The gateway IP should be assigned by your DHCP server.
Check the gateway value with a ifconfig or ipconfig /all
  0  
  0  
#2
Options
Re:No Access Point option in Archer C1200 V2
2017-12-30 17:21:39
I can only setup a static IP for LAN network, there is no option to automatic/dhcp ip address in LAN network. For the LAN the options are IP Address and Subnet mask.
  0  
  0  
#3
Options
Re:No Access Point option in Archer C1200 V2
2018-01-06 22:57:18
same exact problem, bought this as access point but no internet,although i followed TPLINK instructions to the dot.
what to do?
  0  
  0  
#4
Options
Re:No Access Point option in Archer C1200 V2
2018-01-07 17:09:37
new firmware released in december for US model now has this option of operation mode.
hope europe gets it soon too
  0  
  0  
#5
Options
Re:No Access Point option in Archer C1200 V2
2018-01-07 19:03:32
There is a new version for US (v1 and v2) (january 2018) with AP mode added, I hope they release new EU version with AP mode added.
  0  
  0  
#6
Options
Re:No Access Point option in Archer C1200 V2
2018-01-20 04:56:08
I see the Access Point operation mode in the new firmeware release v2 20180108, but when I setup this option the LAN settings in Static IP I only can set static ip address, network mask and gateway, but where do I set the dns servers? I don't see where i can setup the dns servers.

Ciao
  0  
  0  
#7
Options
Re:No Access Point option in Archer C1200 V2
2018-01-20 05:31:10
Normally DHCP should not be on , on the secondary Router (AP only) and it should be plugged to a LAN port Not the Wan port of the main Router so DHCP,DNS etc is all done by the Main Router.

This is how my C7 V2 is configured as it does not have Operation Modes anyway... However if you Bridge the LAN Port on the Main Router (ie your ISP's Router) then you can use the Router normally ...ie DHCP etc is On just make sure they have different IP addresses assigned and note there is no communication between the two Routers on the Lan if Bridged.


KB.
  0  
  0  
#8
Options
where is bridgeing mode on c1200?
2018-01-25 14:57:17
ok now im getting really pissed off by c1200
where is the bridging mode?
please someone help me how to bridge this piece of junk to my tp link vr400 router
how to bridge the wifi network?
  0  
  0  
#9
Options
Re:No Access Point option in Archer C1200 V2
2018-01-26 01:52:58
see my post above yours..... works on every Router I have ever had , but I don't own a C1200 though .... TP link Routers I've had don't have "Modes" like Linksys and others like eg Gateway/Router/AP etc. all they do is set DHCP Off etc for you....

WDS is the Bridge mode of TP-link Routers Wifi I believe, I don't use it
  0  
  0  
#10
Options
Re:No Access Point option in Archer C1200 V2
2018-01-26 16:43:31
The latest firmware for Archer C1200_V2 already support Access Point mode.
  0  
  0  
#11
Options
12

Information

Helpful: 0

Views: 12377

Replies: 13

Related Articles
Archer C1200 as access point
2184 0
Archer C1200 / router and access point issues
595 0
Archer C1200 in access point mode troubleshooting
4624 0
Archer C1200 as access point
1956 0
No Access Point Mode option
141 0
Archer c60 v2 in Access point mode
19330 2
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.