How to set BRIDGE mode
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to set BRIDGE mode
Region : Italy
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.20 Build 120705 Rel.39030n Beta
ISP :
Hi to all,
I'm facing problem to properly set BRIDGE mode (WDS Bridging). I had a router connected to ADSL line with following setting:
IP 192.168.1.1
Security setting - WPA2/TKIP
DHCP on
The wi-fi coverage is not good in all the floor so I'm trying to extend coverage using a TL-MR3220. I did follow the instruction in this video:
http://www.youtube.com/watch?v=OWVPZSQqUZg
But It doesn't work... Enabling WDS bridge mode, I was able to found SSID and set password. I setted the IP address for the MR3220 in 192.168.1.100 and I leave DHCP also on with no IP conflict.
From Diagnostic page I'm able to ping at 192.168.1.1 with good response but If I try to reach 192.168.1.1 from my laptop or smartphone this is not found.
Where do I make mistake?
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.20 Build 120705 Rel.39030n Beta
ISP :
Hi to all,
I'm facing problem to properly set BRIDGE mode (WDS Bridging). I had a router connected to ADSL line with following setting:
IP 192.168.1.1
Security setting - WPA2/TKIP
DHCP on
The wi-fi coverage is not good in all the floor so I'm trying to extend coverage using a TL-MR3220. I did follow the instruction in this video:
http://www.youtube.com/watch?v=OWVPZSQqUZg
But It doesn't work... Enabling WDS bridge mode, I was able to found SSID and set password. I setted the IP address for the MR3220 in 192.168.1.100 and I leave DHCP also on with no IP conflict.
From Diagnostic page I'm able to ping at 192.168.1.1 with good response but If I try to reach 192.168.1.1 from my laptop or smartphone this is not found.
Where do I make mistake?
Re:How to set BRIDGE mode
Hi to all,
I tried again to connect the two lan in bridge mode without result... In picture 1 is rapresented network layout:
When I follow the TP-link FAQ, 192.168.1.3 is able to see 192.168.1.1 with ping command and viceversa. Any user in LAN 2 is able to see 192.168.1.3 but it's impossible to reach 192.168.1.1
I tried a different thing... Connecting directly Lan2 to 192.168.1.1 in wi-fi mode, I'm able to ping 192.168.1.3.
So the matter is why does lan2 is not able to connect to internet through 192.168.1.3 in bridge mode?
Attacched info on 192.168.1.1 router.
Any suggest is much apprecited.
I tried again to connect the two lan in bridge mode without result... In picture 1 is rapresented network layout:
When I follow the TP-link FAQ, 192.168.1.3 is able to see 192.168.1.1 with ping command and viceversa. Any user in LAN 2 is able to see 192.168.1.3 but it's impossible to reach 192.168.1.1
I tried a different thing... Connecting directly Lan2 to 192.168.1.1 in wi-fi mode, I'm able to ping 192.168.1.3.
So the matter is why does lan2 is not able to connect to internet through 192.168.1.3 in bridge mode?
Attacched info on 192.168.1.1 router.
Any suggest is much apprecited.
File:
