MR600 Carrier Aggregation Issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

MR600 Carrier Aggregation Issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
MR600 Carrier Aggregation Issue
MR600 Carrier Aggregation Issue
2020-07-25 15:36:20
Model: Archer MR600  
Hardware Version: V1
Firmware Version: 1.1.0 0.9.1 v0001.0 Build 200417 Rel.75138n

Region: India

 

ISP: Airtel

 

LTE Bands: Band 1, Band 3, Band 8, Band 40

 

 

Hello,

 

I'm using the frst beta firmware to manually enable carrier aggregation on MR600, however I've come across the following issues:

 

1. Manually selecting Band 3 and Band 40 enables the 4G+ mode, but the bands don't remain aggregated indefinitely. Sometimes it remains aggregated for an hour or more while sometimes it remains aggregated only for a couple of minutes. Once the aggregation is lost, the router switches back to Band 40.

 

Why is this happening? Is this an issue with the router or with the cellular tower? 

 

2. My ISP supports intraband aggregation for Band 40, but the MR600, even after manually selecting both bands to Band 40 doesn't aggregate them. The advanced page shows that the router is still using single Band 40. The possible CA combinations on the first page shows that intraband Band 40 aggregation is supported on the MR600. 

 

Again, is this an issue with the router? My iPhone always aggregates Band 40 which gives me the best speeds, so I'm sure that the tower is capable of allowing intraband Band 40 aggregation. 

 

I'd really appreciate if someone can help me out here.

 

Thanks.

  2      
  2      
#1
Options
14 Reply
Re:MR600 Carrier Aggregation Issue
2020-08-10 10:25:39

@LTE-A 

Hello, thank you very much for your time and patience.

For the band aggregation feature on the MR600,  which bands are chosen to aggregate and how these bands are aggregated with each other, they are decided by the cellular tower.

So far, we could still not make sure the issue is on the MR600.

And I wonder if you have a second device which could be used to make a comparison;

Thank you~

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:MR600 Carrier Aggregation Issue
2020-08-11 19:03:37

@LTE-A 

Hi Airtel and JIO both Indian providers supports 2XCA combination in All Indian metros on band 40 with 40A-40A combination and with 3A-40A combination.

But MR600 only supports 3A-40A only for Airtel. And MR-600 currently does not support 40A-40A combination which is well supported by many Indian manufactured mobile devices such as Samsung Galaxy J8, J7 Pro, S7, Oneplus 6, 7, Redmi Note 9 Pro. Poco F1 & F2 etc.

 

TP-Link please implement 40A-40A combination to support 2CA carrier aggregation on Indian providers such as Airtel and JIO on your next general firmware keeping the 4G band selection feature.

 

If you support this 40A-40A combination on MR-600, your MR-600 product will lead the market and it will be the only one best 4G+ wifi router in the Indian market.

 

  5  
  5  
#3
Options
Re:MR600 Carrier Aggregation Issue
2020-08-14 00:49:38
Hey, Good day, Thank you very much for your detailed information. We would report your case to our engineers for further analysis. Your feedback is highly appreciated. Thank you very much.
Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  1  
  1  
#4
Options
Re:MR600 Carrier Aggregation Issue
2020-08-25 11:13:33

@Sunshine Is any update on this. Thanks

I am wondering whether its required hardware version upgrade or it can be delivered thright firmware update. 

  0  
  0  
#5
Options
Re:MR600 Carrier Aggregation Issue
2020-09-01 20:07:48
Hii Using tp-link mr600 Aggregation not happening. Using airtel that support band 3 and band 40. Earlier it happening. Please help
  0  
  0  
#6
Options
Re:MR600 Carrier Aggregation Issue
2020-09-08 09:19:39

@Shashi_vaushali 

Good day.

In this way, please try to update the beta firmware and manually choose the 4G band:

https://static.tp-link.com/2020/202004/20200420/Archer_MR600v1_1.1.0_0.9.1_[200417-rel75138]_up_boot_2020-04-20_08.44.31.zip

Thank you very much!

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#7
Options
Re:MR600 Carrier Aggregation Issue
2020-09-17 08:56:24

@Sunshine 

 

Hello,

 

I have exactly the same problem, Automatic carrier aggregation does not work in MR600. With the help of beta firmware, when i force band 3 and 5 for Jio, Carrier Aggregation works. But the most common Carrier Aggregation with Band 40 + band 40 does not support in this Router. As of now i see that in JIO only Bnad 3 and 5 combination works. I see a lot of people are reporting this problem in TP-Link forum and would like to see a fix from you at the earliest.

 

  0  
  0  
#8
Options
Re:MR600 Carrier Aggregation Issue
2020-09-22 08:40:35
Hello, Do you have any update on this topic? we are waiting for the new firmware to be released which supports band 40+40 CA.
  0  
  0  
#9
Options
Re:MR600 Carrier Aggregation Issue
2020-10-11 17:23:25

@LTE-A 

could you please share some screenshots or steps to enable 4g advanced and which firmware will support this.

my current firmware is 1.2.0 0.9.1 v0001.0 Build 200511 Rel.44954n

I am using airtel sim

  0  
  0  
#10
Options
Re:MR600 Carrier Aggregation Issue
2020-10-23 14:25:08 - last edited 2020-10-23 14:41:02

@LTE-A Can anyone help how to enable 4G+, its turned off that 4G+ LED is not glowing. In India, Chennai Metro city using Airtel 

  0  
  0  
#11
Options