2 ips on Archer VR400 V2 ac1200(not A2300 as below)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

2 ips on Archer VR400 V2 ac1200(not A2300 as below)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
2 ips on Archer VR400 V2 ac1200(not A2300 as below)
2 ips on Archer VR400 V2 ac1200(not A2300 as below)
2020-08-30 12:42:41 - last edited 2020-09-17 01:46:40
Model: Archer A2300  
Hardware Version: V2
Firmware Version:

Hi I give a second ip on my router for example, one is 192.168.1.1 , the other is 192.168.7.1 and i have two computers in the first network and another third one pc in the second network. When i try to ping to one pc from the first network to the third pc to the other network it fails although i am able to ping to 192.168.1.1 and to 192.168.7.1 and connect to the internet too from all the pc's.Any suggestion?      

  0      
  0      
#1
Options
1 Accepted Solution
Re:2 ips on Archer VR400 V2 ac1200(not A2300 as below)-Solution
2020-09-17 01:46:28 - last edited 2020-09-17 01:46:40

@konstantinosdms 

Good day.

Sorry for the delay.

May I know where did you set up the second IP? It is in the attached picture?

Or do you also have two routers, one of them has IP address 192.168.1.1 with DHCP IP range: 192.168.1.xxx, the other is 192.168.7.1 with DHCP IP range 192.168.7.xxx, and the two routers are connected one by one?

Such as: internet—ISP—router 1(192.168.1.1)---router(192.168.7.1);

 

If it is the second situation,  there is no problem if you want to access from 192.168.7.1 to 192.168.1.1; but there would be some issue from 192.168.1.1-192.168.7.1 since there would be a NAT router and would block the connection;

So you could try to open the ports for the devices behind router 2;

 

Thank you very much.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:2 ips on Archer VR400 V2 ac1200(not A2300 as below)-Solution
2020-09-17 01:46:28 - last edited 2020-09-17 01:46:40

@konstantinosdms 

Good day.

Sorry for the delay.

May I know where did you set up the second IP? It is in the attached picture?

Or do you also have two routers, one of them has IP address 192.168.1.1 with DHCP IP range: 192.168.1.xxx, the other is 192.168.7.1 with DHCP IP range 192.168.7.xxx, and the two routers are connected one by one?

Such as: internet—ISP—router 1(192.168.1.1)---router(192.168.7.1);

 

If it is the second situation,  there is no problem if you want to access from 192.168.7.1 to 192.168.1.1; but there would be some issue from 192.168.1.1-192.168.7.1 since there would be a NAT router and would block the connection;

So you could try to open the ports for the devices behind router 2;

 

Thank you very much.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 1054

Replies: 1

Related Articles