Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > TP AX1800 with DHCP off : Wireless devices can't connect

< All Threads

TP AX1800 with DHCP off : Wireless devices can't connect

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TP AX1800 with DHCP off : Wireless devices can't connect

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Wallakam

2020-12-10 10:48:26 - last edited 2020-12-15 01:53:54

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2020-12-10

TP AX1800 with DHCP off : Wireless devices can't connect

2020-12-10 10:48:26 - last edited 2020-12-15 01:53:54

Model: Archer AX1800

Hardware Version:

Firmware Version:

Background

Since the wireless signal from my home router (connected to the ISP) is not reaching specific parts of the house, i decided to buy an AX1800 and connect as a "bridge", by bridge i mean having the AX1800 as a switch without DHCP.
To do that, i connected both routers via the normal ports (not WAN), but DHCP still on. The connection was bad, i had some packet loss and the ping got higher!
So, i decided to disable DHCP on the AX1800 which allowed better connection on the wired devices.
I am not using AP mode (for many reasons).

Problems

After turning off DHCP, wired devices connect excellently but wireless devices can't connect at all to the AX1800, why?
Which uplink port should be used on the AX1800 to the home router?
Should NAT be on/off?

Thank You.

1 Accepted Solution

terziyski

LV7

2020-12-10 15:20:18 - last edited 2020-12-15 02:06:05

Posts: 7138

Helpful: 5352

Solutions: 1219

Stories: 7

Registered: 2013-10-12

Re:TP AX1800 with DHCP off : Wireless devices can't connect-Solution

2020-12-10 15:20:18 - last edited 2020-12-15 02:06:05

Your are using this scenario. The second one is this one.

Both NAT and DHCP should be OFF (althogh, if you are not using the blue poort - Internet, you can leave NAT as is).

In your scenario the LAN port of AX1800 should be used for connecting to the home router.

Wireless devices should connect fine as well cause wi-fi is just a bridge to the LAN of the device.

I am wondering why wouldn't you give a try to AX1800 in AP mode - second scenario ?

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".

Recommended Solution

3 Reply

terziyski

LV7

2020-12-10 15:20:18 - last edited 2020-12-15 02:06:05

Posts: 7138

Helpful: 5352

Solutions: 1219

Stories: 7

Registered: 2013-10-12

Re:TP AX1800 with DHCP off : Wireless devices can't connect-Solution

2020-12-10 15:20:18 - last edited 2020-12-15 02:06:05

Your are using this scenario. The second one is this one.

Both NAT and DHCP should be OFF (althogh, if you are not using the blue poort - Internet, you can leave NAT as is).

In your scenario the LAN port of AX1800 should be used for connecting to the home router.

Wireless devices should connect fine as well cause wi-fi is just a bridge to the LAN of the device.

I am wondering why wouldn't you give a try to AX1800 in AP mode - second scenario ?

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".

Information

Helpful: 0

Replies: 3

TP AX1800 with DHCP off : Wireless devices can't connect

TP AX1800 with DHCP off : Wireless devices can't connect

Information

Voters 0

Tags