Home Network Community > All Threads > Using bridge mode with Vr400
< All Threads

Using bridge mode with Vr400

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Using bridge mode with Vr400

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Using bridge mode with Vr400
Using bridge mode with Vr400
2020-12-20 18:07:00 - last edited 2020-12-21 00:56:32
Model: Archer VR400  
Hardware Version: V2
Firmware Version:

I would like to change to Vr400 to modem.

When I change the internet set up to bridge I don't see where can I enter the username and password of the service provider.

I intend to connect the Vr400 to eero mesh,

 

thanks

 

Ilan

  0      
 
  0      
 
#1
Options
6 Reply
Re:Using bridge mode with Vr400
2020-12-20 18:26:45 - last edited 2020-12-21 00:56:32

@Zidko 

 

Is than you are looking for:

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:Using bridge mode with Vr400
2020-12-20 19:48:48 - last edited 2020-12-21 00:56:32

@Ivaylo when I am selecting bridge , i dont see these two windows. Where can I set up the modem connection?

  0  
  0  
#3
Options
Re:Using bridge mode with Vr400
2020-12-21 07:01:24

@Ivaylo enclosed is the screen picture when i use bridge:

 

  0  
  0  
#5
Options
Re:Using bridge mode with Vr400
2020-12-21 11:00:21
OK, now it's clearer what you're trying to achieve. If connection type is bridge, the PPPoE session (where the username and password are put in) should be initiated on the device that is bridged to your VR400 (i.e. next connected device - your wireless router, your PC/Laptop, etc.).
If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#6
Options
Re:Using bridge mode with Vr400
2020-12-22 08:32:25

@Ivaylo thanks. I managed to do it, Can i keep the tp link wireless network on and in parallel to use the mesh wifi network as well? 

  0  
  0  
#7
Options
Re:Using bridge mode with Vr400
2020-12-22 11:27:00
In that particular scenario (bridge mode) it is advisable to turn it off if the next device (your wi-fi router) is near to the VR400.
If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#8
Options

Information

Helpful: 0

Views: 5978

Replies: 6

Related Articles
Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco
21311 0
AX12 + VR400 (v3) - OneMesh + Bridge Mode
1768 0
Archer VR400 v3 - Bridge Mode Question
1009 0
TP-Link VR400 Bridge Mode on Sky Fibre
5824 0
Archer VR400 Modem Mode/Transparent Bridging Mode
5441 0
Bridge Mode Archer vr500v
3946 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.