Deco M5 Signal Source not connected to ethernet

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Deco M5 Signal Source not connected to ethernet

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco M5 Signal Source not connected to ethernet
Deco M5 Signal Source not connected to ethernet
2021-06-04 12:09:13
Model: Deco M5  
Hardware Version:
Firmware Version: 1.5.3

Hi there, 

 

Just set up my 3 Decos. I connected all 3 M5s to my router and set up the main Deco and the slaves. So far all good, however, I have one deco showing Signal Source as Ethernet and the other one showing as wifi with the name of the main deco. 

 

Why is it not showing as ethernet? the cable is connected directly from modem to deco... 

 

Am I doing something wrong?

  0      
  0      
#1
Options
11 Reply
Re:Deco M5 Signal Source not connected to ethernet
2021-06-04 12:36:25

Also - the one which has the Signal source as ethernet keeps disconnecting

  0  
  0  
#2
Options
Re:Deco M5 Signal Source not connected to ethernet
2021-06-04 12:53:41
  0  
  0  
#3
Options
Re:Deco M5 Signal Source not connected to ethernet
2021-06-04 13:09:45

@Alexandre. My setup is how its stated in the link you sent me. I have main deco connected directly to the modem then the other two decos are connected directly by cat6 to the modem. Why is one marked as ethernet and one wifi? the one with the etherner is flapping also 

  0  
  0  
#4
Options
Re:Deco M5 Signal Source not connected to ethernet
2021-06-04 13:21:17

@TUMAS 

 

What is your Deco mesh Operating Mode? You can that it in Deco app, under Advanced:

 

  0  
  0  
#5
Options
Re:Deco M5 Signal Source not connected to ethernet
2021-06-04 13:25:20

@Alexandre. It's set as wireless router(Recommended) however when i try to click on access point it wont let me.. How should it be? I have all my decos connected with independant CAT6 cables to the modem

  0  
  0  
#6
Options
Re:Deco M5 Signal Source not connected to ethernet
2021-06-04 13:48:23

@TUMAS 

 

This is from the link I provided:

 

In Router mode: Only the main Deco could be connected to your home modem/router. Other satellite Deco units should be connected behind the main one, just as the “Star Network” shows. If not, they may be in a network loop and cause unexpected dropout issues.

  0  
  0  
#7
Options
Re:Deco M5 Signal Source not connected to ethernet
2021-06-04 14:01:29

@Alexandre. So the second port of the main should connect directly to the switch?

  0  
  0  
#8
Options
Re:Deco M5 Signal Source not connected to ethernet
2021-06-04 14:11:03

 

TUMAS wrote

@Alexandre. So the second port of the main should connect directly to the switch?

@TUMAS 

 

Yes, this is how it works for Deco mesh running in Router mode.

 

  0  
  0  
#9
Options
Re:Deco M5 Signal Source not connected to ethernet
2021-06-04 18:54:36

@Alexandre. Ok so I connected the switch with thw other two decos to the second port of the deco and now both decos have ethernet as signal. Is that the best way to be configured? Is all the bandwidth passing through the deco like that being its own bottleneck?

  0  
  0  
#10
Options
Re:Deco M5 Signal Source not connected to ethernet
2021-06-04 19:55:07 - last edited 2021-06-04 19:55:52

@TUMAS 

 

This is the only way to configure Deco mesh running in Router mode, if you want to have Ethernet backhaul on Satellite Deco.

 

If you want, you can change Deco to Access Point mode. You'll lose very many features offered by Deco, but in AP mode you can wire Deco units any way you want, including connecting them all directly to your ISP router.

I do not need anything from Deco other than WiFi coverage, my Deco mesh runs in Access Point mode.

 

You said you had problems switching Deco to AP mode, I suspect it were because your WiFi mesh was unstable. Now that it is properly wired for Router mode, you can try again. After you see it switched to AP mode, you can rewire Deco units the way you want.

If in Deco app you still can't switch from Router to Access point mode, I suggest you create new post with corresponding subject, and see if someone or TP-Link support can assist you.

 

Does not matter how Decos are wired, assuming you use gigabit switch and knowing that Deco M5 have gigabit ports, it is unlikely your home network will experience bottleneck. Even if you keep everything as is, in Router mode.

  0  
  0  
#11
Options

Information

Helpful: 0

Views: 2775

Replies: 11

Related Articles