I can't access a tplink router wr840N which is behind WR940N

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

I can't access a tplink router wr840N which is behind WR940N

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
I can't access a tplink router wr840N which is behind WR940N
I can't access a tplink router wr840N which is behind WR940N
2021-07-18 07:36:12 - last edited 2021-08-04 10:31:13
Model: TL-WR940N  
Hardware Version: V6
Firmware Version:

I have a question and searched too much could not find any solution.

I describe my scenario :

Assume I am connected with ISP Modem, from LAN port of archer I connect to TP-Link MAIN router's WAN,

From TP-Link Main router's LAN connected more 5 routers on their WAN ports.

while connected to ISP Modem I can access My TP-Link Main router WR940n But can't access all other SUB routers (already enabled remote web access of sub routers).

When connected to tplink Main router I can access all sub routers.

I want to access all sub routers (4 tplink) while I am on ISP modem.

 

ISP Modem : Archer C60
Main Router : WR940N
Sub routers : WR840n

 

  0      
  0      
#1
Options
1 Accepted Solution
Re:I can't access a tplink router wr840N which is behind WR940N-Solution
2021-08-04 08:07:00 - last edited 2021-08-04 11:51:04

@Jdhn 

 

To be able to access WebGUI of sub routers when connected to C60 router, you have to configure a virtual servers on wr940n (main router) for every single sub router.

For example.

 

First sub router:

 

 

Second sub router:

 

 

etc.

given that every sub router remote management port is 8080 (internal port in screenshots above).

When connected to C60 router in browser type:

http://192.168.100.254:8081 for the first sub router

http://192.168.100.254:8082 for the second sub router

etc.

 

 

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
Recommended Solution
  1  
  1  
#2
Options
8 Reply
Re:I can't access a tplink router wr840N which is behind WR940N-Solution
2021-08-04 08:07:00 - last edited 2021-08-04 11:51:04

@Jdhn 

 

To be able to access WebGUI of sub routers when connected to C60 router, you have to configure a virtual servers on wr940n (main router) for every single sub router.

For example.

 

First sub router:

 

 

Second sub router:

 

 

etc.

given that every sub router remote management port is 8080 (internal port in screenshots above).

When connected to C60 router in browser type:

http://192.168.100.254:8081 for the first sub router

http://192.168.100.254:8082 for the second sub router

etc.

 

 

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
Recommended Solution
  1  
  1  
#2
Options
Re:I can't access a tplink router wr840N which is behind WR940N
2021-08-04 10:32:53
At Last! After a long time I did. Thank you very much. I will spread this solution as much I can... 🌹❤️
  0  
  0  
#3
Options
Re:I can't access a tplink router wr840N which is behind WR940N
2021-08-04 12:59:36

@terziyski 

Dear I want to add some thing which is in the same network.

 

I have attached an AP to a router and being on the same ISP router I want to access its interface. When I am inside i can access that AP with this link "http://tplinkap.net/".

The scenario is:


Sub Router

WAN 192.168.10.123

LAN 192.168.0.1

 

AP TL-WA801ND

Lan 192.168.0.115 (reserved in DHCP)

 

What should and where should I add this as virutal server so that i am able to access from ISP Modem.?

  0  
  0  
#5
Options
Re:I can't access a tplink router wr840N which is behind WR940N
2021-08-04 14:37:24 - last edited 2021-08-05 10:02:23

@Jdhn 

 

Try these settings:

 

On main router - 192.168.100.254 (wr940n):

 

 

On sub router - 192.168.10.123 (wr840n):

 

 

When connected to C60 browse the following URL:

http://192.168.100.254:8091

If you're connected to the main router (wr940n) browse the following URL:

http://192.168.10.123:8090

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  0  
  0  
#6
Options
Re:I can't access a tplink AP WA-840ND which is behind WR940N
2021-08-09 08:28:01

@terziyski 

 

I am very thank ful for all your assistance and I have did all as per your guidance. Remaining only one issue which is:

 

WR940N (Main TP-Link)            192.168.100.254

 

WR940N (Sub Router)               192.168.10.121

 

TL-WA801ND (Access Point)     192.168.3.150 

 

I have added like:

 

In Main router : (http not work that's why add ssl port)

 

on sub router : ( checked with both http (80) and ssl (443)

 

 

in the above cases sub router i can access but I need to access tplink AP (192.168.3.150).

 

If you recommend in the topology I will appreciate your suggestion.

 

Thank you very much,,,

 

Regards,

Jawad Hussain.

  0  
  0  
#7
Options
Re:I can't access a tplink AP WA-840ND which is behind WR940N
2021-08-09 08:48:22 - last edited 2021-08-09 10:47:40

@Jdhn 

 

On the main router (WR940n) replace the internal port 443 with 8090 and save the settings:

Here I assume that you're using port 80 for TL-WA801ND WebGUI access (when you're connected to it).

When connected to main router (WR940N-192.168.100.254) browse the following URL:

http://192.168.100.254:8091

If you're connected to the sub router (WR940N-192.168.10.121) browse the following URL:

http://192.168.10.121:8090

 

Both port-forwards are having the goal for accessing the TL-WA801ND (Access Point) -192.168.3.150 WebGUI.

Take a look at my previous post and see the similarity with this one, but with different IP addresses according to your previous request.

For accessing the main router or sub-router WebGUI - that's different - refer to my first post.

 

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  0  
  0  
#8
Options
Re:I can't access a tplink AP WA-840ND which is behind WR940N
2021-08-09 08:52:21
By this I can't even login to sub router if keep port of 80 or 8090. means to say port 80 or related i can't login to sub router even.
  0  
  0  
#9
Options
Re:I can't access a tplink AP WA-840ND which is behind WR940N
2021-08-11 06:22:14
I will check again following your post and then reply you once finish. Is there may be the issue with the access point as that one is very old ? thank you
  0  
  0  
#10
Options

Information

Helpful: 0

Views: 1869

Replies: 8

Related Articles