4G Band Selection in MR-600 V1 with latest Beta Software

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

4G Band Selection in MR-600 V1 with latest Beta Software

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
4G Band Selection in MR-600 V1 with latest Beta Software
4G Band Selection in MR-600 V1 with latest Beta Software
2023-03-17 04:38:01 - last edited 2023-10-09 05:09:38
Model: Archer MR600  
Hardware Version: V1
Firmware Version: Archer_MR600(EU)_V1_220818

With the latest beta software in MR-600V1 i want to select bands 40 & 40 unfortunately no option of Selection 40,40, I can select some other combination like 3,40 but want to select 40,40 - how to do that ? Please advice ( Leaving it in Auto Band Selection mode chooses only one band - with the old beta software, i was able to select 40,40 and MR600 was working with carrier aggregation in 40,40. Please advice

  0      
  0      
#1
Options
1 Accepted Solution
Re:4G Band Selection in MR-600 V1 with latest Beta Software-Solution
2023-03-27 15:19:32 - last edited 2023-10-09 05:09:38

  Sunshine wrote

  @senpoos1 

 

Hi, for MR600, when selecting band 40 only, it means the router allows using 40, 40 as well, but whether it can be aggregated is decided by the base station as well, thus we are unable to force it to aggregate, if your ISP supports other band combinations in 4G+, please also try to select other band(s).

@Sunshine Something is wrong with the latest beta firmware, Unfortuantley it does select only 1 4G band 40 with the latest Beta firmware ( Archer_MR600(EU)v1_1.2.0_0.9.1). I went back to the older Beta firmware ( Archer_MR600v1_1.1.0_0.9.1 )  and was able connect to B40 & B40 Carrier aggregation is working fine with older beta version frimware

Recommended Solution
  0  
  0  
#3
Options
2 Reply
Re:4G Band Selection in MR-600 V1 with latest Beta Software
2023-03-20 02:51:36

  @senpoos1 

 

Hi, for MR600, when selecting band 40 only, it means the router allows using 40, 40 as well, but whether it can be aggregated is decided by the base station as well, thus we are unable to force it to aggregate, if your ISP supports other band combinations in 4G+, please also try to select other band(s).

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:4G Band Selection in MR-600 V1 with latest Beta Software-Solution
2023-03-27 15:19:32 - last edited 2023-10-09 05:09:38

  Sunshine wrote

  @senpoos1 

 

Hi, for MR600, when selecting band 40 only, it means the router allows using 40, 40 as well, but whether it can be aggregated is decided by the base station as well, thus we are unable to force it to aggregate, if your ISP supports other band combinations in 4G+, please also try to select other band(s).

@Sunshine Something is wrong with the latest beta firmware, Unfortuantley it does select only 1 4G band 40 with the latest Beta firmware ( Archer_MR600(EU)v1_1.2.0_0.9.1). I went back to the older Beta firmware ( Archer_MR600v1_1.1.0_0.9.1 )  and was able connect to B40 & B40 Carrier aggregation is working fine with older beta version frimware

Recommended Solution
  0  
  0  
#3
Options

Information

Helpful: 0

Views: 788

Replies: 2

Related Articles