Home Network Community > All Threads > Archer VR2800 Slow WAN in Wireless Access Point Mode
< All Threads

Archer VR2800 Slow WAN in Wireless Access Point Mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer VR2800 Slow WAN in Wireless Access Point Mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer VR2800 Slow WAN in Wireless Access Point Mode
Archer VR2800 Slow WAN in Wireless Access Point Mode
2023-09-20 15:52:46 - last edited 2023-09-22 09:21:53
Model: Archer VR2800  
Hardware Version: V1
Firmware Version: 0.7.0 0.9.1 v006c.0 Build 210313 Rel.74106n

Hi All,

 

Hope someone can help me with the below.

 

I've just switched from FTTC VDSL to a full FTTP setup using a ONT setup and wanted to use my Archer VR2800 as the ISP router is poor. However on setup it looks like my VR2800 won't handle speeds greater than 300mbps using LAN4/WAN port in Wireless Router Mode??

 

Is this right and the DSL version is restricted to max 300mbps and will not work with my 1gig connection? or am I just setting it up wrong?

 

Thanks

 

 

Nova

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Archer VR2800 Slow WAN in Wireless Access Point Mode-Solution
2023-09-20 20:36:03 - last edited 2023-09-22 09:21:53

  @Novascape 

 

VR2800 supports 1000mbps bandwidth on its LAN ports. Try the following:

There's a newr FW release that you can update manually - download FW from here.

After update you can reset the VR2800 to its factory defaults and then configure in wireless router mode.

Here's a video guide for setting up VR2800 in wireless router mode.

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
Recommended Solution
  1  
  1  
#2
Options
3 Reply
Re:Archer VR2800 Slow WAN in Wireless Access Point Mode-Solution
2023-09-20 20:36:03 - last edited 2023-09-22 09:21:53

  @Novascape 

 

VR2800 supports 1000mbps bandwidth on its LAN ports. Try the following:

There's a newr FW release that you can update manually - download FW from here.

After update you can reset the VR2800 to its factory defaults and then configure in wireless router mode.

Here's a video guide for setting up VR2800 in wireless router mode.

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
Recommended Solution
  1  
  1  
#2
Options
Re:Archer VR2800 Slow WAN in Wireless Access Point Mode
2023-09-20 22:36:43

  @terziyski  thanks that's fixed it. Wan in wireless mode is now doing 1gb.

 

Now it's working the WiFi is not fast enough 😅

  0  
  0  
#3
Options
Re:Archer VR2800 Slow WAN in Wireless Access Point Mode
2023-09-22 02:38:25

  @Novascape 

 

Here's a guide on how to optimize your wireless speed and range.

For better wireless speed it is recommended to use your 5GHz band.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  1  
  1  
#4
Options

Information

Helpful: 0

Views: 726

Replies: 3

Related Articles
VR2800 WIreless Access Point mode
910 0
Archer AX50 as a wireless Access Point
82 0
VR2800 Wireless Router Mode - MER
2278 0
5ghz slow on Archer C50 as Access point
1383 0
Failure to set up Archer VR2800
1074 0
Archer VR2800 & Virgin Hub3
1218 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.