flapping Powerline network
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
flapping Powerline network
Model :
TL-PA511 & TP-PA4030
Hardware Version : Not Clear
Firmware Version : unknown
ISP : BT
big Powerline fan! been running them successfully for many years. :)
currently run the 600Mbs 5plug system in my own home, having upgraded from the 500Mbps...
the old 500Mbps plugs where then fitted in a friends home, again 5 in total.
But I have never known a Powerline network to be so flappy! :(
I dont think its faulty plugs as I was using them without issue.
This is the second set I have fitted there. So I suspect its a wiring issue in the home?
using the utility to monitor the network it continually defaults the Names i have set....thats one issue:
If I open the window I see the following 3 plugs only:
Living Room - 55Mbps
Orangrey - 168Mbps
Annex - 229Mbps
(note the poor speed on the living room plug)
and then intermittently it changes to
Living room - 55Mbps
Annex - 229Mbps
Bedroom - 60Mbps
(again a very poor speed on the Bedroom, but also note the Living Room has vanished!)
The house has had some electrical issues and had the main consumer unit replaced due to being insufficient for the load. But have been assured the wiring is good (except the living room)
The Living Room currently has some temporary wiring in place, and I'm beginning to wonder if that is an indication to something not being normal behind the walls in the rest of this home.
I have only ever seen one oddity with Powerline plugs and that was fixed by securing the network in another place.
All 5 of these plugs are secured, but I continually loose connection from the Bedroom and the Annex (both have Apple WiFi Access Points attached)
Any thoughts on what could be going on, or things I should try to get a stable LAN
Draytek Router
Apple Airport Express x 2
5 Powerline 500Mbps plugs (some are 3 port)
TIA
Hardware Version : Not Clear
Firmware Version : unknown
ISP : BT
big Powerline fan! been running them successfully for many years. :)
currently run the 600Mbs 5plug system in my own home, having upgraded from the 500Mbps...
the old 500Mbps plugs where then fitted in a friends home, again 5 in total.
But I have never known a Powerline network to be so flappy! :(
I dont think its faulty plugs as I was using them without issue.
This is the second set I have fitted there. So I suspect its a wiring issue in the home?
using the utility to monitor the network it continually defaults the Names i have set....thats one issue:
If I open the window I see the following 3 plugs only:
Living Room - 55Mbps
Orangrey - 168Mbps
Annex - 229Mbps
(note the poor speed on the living room plug)
and then intermittently it changes to
Living room - 55Mbps
Annex - 229Mbps
Bedroom - 60Mbps
(again a very poor speed on the Bedroom, but also note the Living Room has vanished!)
The house has had some electrical issues and had the main consumer unit replaced due to being insufficient for the load. But have been assured the wiring is good (except the living room)
The Living Room currently has some temporary wiring in place, and I'm beginning to wonder if that is an indication to something not being normal behind the walls in the rest of this home.
I have only ever seen one oddity with Powerline plugs and that was fixed by securing the network in another place.
All 5 of these plugs are secured, but I continually loose connection from the Bedroom and the Annex (both have Apple WiFi Access Points attached)
Any thoughts on what could be going on, or things I should try to get a stable LAN
Draytek Router
Apple Airport Express x 2
5 Powerline 500Mbps plugs (some are 3 port)
TIA