Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > Help with bridge mode td-w8950n

< All Threads

Help with bridge mode td-w8950n

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Help with bridge mode td-w8950n

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

kitalor

2016-10-03 10:03:53

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2016-10-03

Help with bridge mode td-w8950n

2016-10-03 10:03:53

Model : Model No. TD-W8950N

Hardware Version : TD-W8950N V1 0x00000001

Firmware Version : 1.1.1 Build 160203 Rel.51377

ISP : tpg australia

Hello
I am attempting to put this modem into full bridge mode to use with an asus router ac68u (through ethernet) but I am having some issues.

I can start from factory default -quick setup enter vpi and vci and set to bridging this way.

However something is not right as after resetting and connecting router I get access but its very unstable. Are there additional settings to be concerned about?

I have ruled out the router as I am currently using another (asus) modem in bridge mode and everything is working. I want to get the w8950n working though as that has the chipset more suited to my adsl2 connection

Any help greatly appreciated!

1.1.1 Build 160203 Rel.51377

4 Reply

kitalor

LV1

2016-10-05 15:31:21

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2016-10-03

Re:Help with bridge mode td-w8950n

2016-10-05 15:31:21

Hello---- echo ---- anybody out there???
THis has been drivingg me insane!!!!!!!!!:mad::mad::mad::mad::mad::mad::mad::mad::mad::mad::mad:
I think I solved it. so after a hard reset for whatever reason all the data isn't cleared..
If I go to advance setup - wan service I get one of these;

Interface	Description	Type	Vlan8021p	VlanMuxId	Igmp	NAT	Firewall	IPv6	Mld	Remove	Edit
atm0.1	br_0_8_35	Bridge	N/A	N/A	Enabled	Disabled	Disabled	Disabled	Disabled

Now this would be there even after a hard reset so I removed it and then went to the quick setup and did a bridge and now everything appears to be stable

now I seem to be able to access both my router and my modem on differnet ip's.

Is this normal? Does it mean I'm not fully bridged?

kitalor

LV1

2016-10-05 19:07:36

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2016-10-03

Re:Help with bridge mode td-w8950n

2016-10-05 19:07:36

still not solved

jimasek

LV5

2016-10-07 03:04:29

Posts: 2171

Helpful: 87

Solutions: 0

Stories: 0

Registered: 2013-01-12

Re:Help with bridge mode td-w8950n

2016-10-07 03:04:29

I'd like to see some of screenshots from your router setup

kitalor

LV1

2016-10-07 07:18:22

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2016-10-03

Re:Help with bridge mode td-w8950n

2016-10-07 07:18:22

Thanks for replying!

http://imgur.com/mdopoli
http://imgur.com/r0dL6NU

I believe I have fixed it. The problem was a dell laptop on the network. It had all sorts of problems after upgrading to windows 10.
I think it was casuing an ip conflict causing modem hangups? I had no idea such a thing was possible
Installed fresh ssd and windows 10 on this laptop and there are no error entries in the router log from the last 24 hours

kitalor

2016-10-03 10:03:53

Posts: 4

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2016-10-03

Information

Helpful: 0

Replies: 4

Help with bridge mode td-w8950n

Help with bridge mode td-w8950n

Information

Voters 0

Tags