Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > Archer C2 AP. DHCP Problems

< All Threads

Archer C2 AP. DHCP Problems

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer C2 AP. DHCP Problems

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

GottHoernchen

2017-06-20 02:40:27

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2017-06-20

Archer C2 AP. DHCP Problems

2017-06-20 02:40:27

Model :

Hardware Version :

Firmware Version :

ISP :

I just recently bought an archer C2 (AC750) router, to replace my old TP link router. Theres to say, I dont use it as a router, but as an accesspoint, behind a fiber router.
The Fibre-Router hosts the DHCP:
DHCP Range: 192.168.1.64 to 253. The router itself taking 254.
I assigned the Archer the IP 253 and disabled DHCP, NAT and nearly everything else.

I have internet access, but in short periods all my clients lose connection (several pcs and wlan clients)

The log from C2 look like that:

1	2017-06-19 20:31:11	DHCPC	Notice	Recv no OFFER, DHCP Service unavailable
2	2017-06-19 20:31:08	DHCPC	Notice	Send DISCOVER with request ip 0.0.0.0 and unicast flag 0
3	2017-06-19 20:31:05	DHCPC	Notice	Send DISCOVER with request ip 0.0.0.0 and unicast flag 0
4	2017-06-19 20:31:00	DHCPC	Notice	Send DISCOVER with request ip 0.0.0.0 and unicast flag 1
5	2017-06-19 20:30:57	DHCPC	Notice	Send DISCOVER with request ip 0.0.0.0 and unicast flag 1
6	2017-06-19 20:30:54	DHCPC	Notice	Send DISCOVER with request ip 0.0.0.0 and unicast flag 1

I already updatet the firmware. The Subnetmask ist 255.255.0.0 on both, the Router and the C2.

Any Ideas where the issue could have its origin?

Regards
Tim

2 Reply

flying snow

LV4

2017-07-13 18:39:44

Posts: 777

Helpful: 70

Solutions: 0

Stories: 0

Registered: 2017-06-28

Re:Archer C2 AP. DHCP Problems

2017-07-13 18:39:44

configure the wan to static and put ip address like 10.0.0.1 to it so router won't send DHCP to wan side.
pcs are connected to C2 or main router? wired or wireless? when they those internet, can they still ping the gateway?

dme3

LV1

2021-03-25 13:04:06 - last edited 2021-03-25 13:08:45

Posts: 12

Helpful: 4

Solutions: 0

Stories: 0

Registered: 2021-02-18

Re:Archer C2 AP. DHCP Problems

2021-03-25 13:04:06 - last edited 2021-03-25 13:08:45

I have exactly the same problem with a C2300 v1 running the latest firmware (2.0.3 which is quite old, from 09/2018).

While in Access Point mode, it keeps sending DHCP requests every ˜10 seconds even if the IP address is static.

Changing IP address from Static to Dynamic and then back to Static solves the problem, but it is temporary. Rebooting the router the issue appears again and the device starts flooding the network with DHCP requests again.

Making the IP Dynamic and reserving it on the main router does have the same effect (temporarily solves the problem until the next reboot/power cycle).

This is clearly a defect in the firmware, something that TP-Link should fix, but a more recent firmware is only available for the “v2” and the “v1” seems to be abandoned.

Shame on you TP-Link to treat your products and customers like this.

PS: I am crossposting this on purpose since TP-Link is ignoring this issue since this product was launched - see also another threads about the this exact same (and unsolved) problem at:

https://community.tp-link.com/en/home/forum/topic/105793

https://community.tp-link.com/en/home/forum/topic/156045

https://community.tp-link.com/en/home/forum/topic/183706

https://community.tp-link.com/en/home/forum/topic/98158 (this topic)