Switches
I got a problem with my home network. I have my smart TVs in my IoT VLAN and my Apple devices in my main VLAN. With version 1.3.6 [2025.12.30] of the ER8411 and the version 1.20.20 (or maybe an older
By
Julian2111
· Latest post 2 hours ago
by Gabriel-TP
0Helpful
55Views
Hi, Since I was updating the newly released firmware on my switches, I noticed that one of the switches has potentially caught of an issue since the firmware upgrade and it will not supply POE to any
PoEFirmware Update
By
KBhuva
· Latest post 9 hours ago
by Gabriel-TP
0Helpful
107Views
Knowledge BaseA Quick Guide to 802.1Q VLANs
If you’re just getting into networking, one concept you’ll want to learn is VLANs (Virtual Local Area Networks). VLANs are a way to separate a network into distinct parts and keep them isolated from e
VLAN & Multi-NetworksOfficial
1Helpful
243Views
I have read several articles about ES205G / GP not showing IP addresses of connected clients when working in controller mode. Sadly, issue still persists, because recently I installed ES205G in my net
ConfigurationFirmware UpdateController
3Helpful
1163Views
Good afternoon community. I am not sure if what I want to do is possible but let's try I have a little RACK with 2 fibre ONTs with direct DHCP WAN IP, no VLAN, no PPPoE The RACK is connected by only o
VLAN & Multi-NetworksNetwork ConnectivityDHCP Service
By
3dat_Peter
· Latest post Thursday
by 3dat_Peter
0Helpful
107Views
Early AccessSG6xx Switches Pre-Release Firmware Adapted to SDN Controller 6.1.0 (Released on Jun 18th, 2026)
This Article Applies to SG6428X V1.20 SG6654X V1.20 SG6428XHP V1.20 SG6654XHP V1.20 Release Notes New Features: Add support for PTP and IEEE 802.1AS on L3 switches for time synchronization in medium a
By
Vincent-TP
Vincent-TP0Helpful
186Views
ES210X-M2 natively supports cable test function (I've been using it) but after adoption to Omada V6 it says cable test is not supported on this device. Why is that?
ControllerCable Test
1Helpful
111Views
I have two SX3008F's. One of them, for some reason, always gets stuck on boot. I hooked up the serial port and found that every time it starts up, it gets interrupted by bootutil and needs me to hit '
0Helpful
274Views
Affected Hardware: SG2008P v3.20 (Firmware: 3.20.24) SX3206HPP v1.20 (Firmware:1.20.23) Environment Context: The network consists of multiple Omada devices (ER8411 v1.0, SX3206HPP v1.20, SG2008P v3.20
SNMP
By
mbze430
1Helpful
95Views
Setup I have a SG2210XMP-M2 v1.0 switch connected to 3 POE cameras on ports 2, 3 and 4. Wifi AP EAP670 is on port 1. No Omada cloud controller, just using the web interface. The cameras power on and w
By
Harold3457
· Latest post Tuesday
by Vincent-TP
0Helpful
179Views
Hello, This applies to all my Omada switches. Every 15 seconds, each switch sends out a DNS request to omada. It fills up my logs with unnecessary requests. I run my switches as standalone and I assum
9Helpful
2311Views
Hi, My OC300 has just prompted me to upgrade the firmware on my SG3210 v3.20 switch from firmware version v3.20.23 Build 20260423 Rel 25947 to firmware version v3.20.24 Build 20260509 Rel.23533 My swi
sg3210
0Helpful
379Views