Business Community > Routers > Backup Wan Don't Work
< Routers

Backup Wan Don't Work

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Backup Wan Don't Work

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Backup Wan Don't Work
Backup Wan Don't Work
2020-02-14 18:02:46 - last edited 2021-04-19 11:29:57
Model: TL-ER5120  
Hardware Version: V3
Firmware Version: 3.0.3 Build 20180830 Rel.66624

Good afternoon people,

 

I have this load at my home and at a client's, but we are suffering from it in cases of connection drop from WAN 1 which I always consider as the main one.

 

If there is a drop in WAN1, but it is still connected, the connection is not passed to WAN 2, even if the detection modes are automatic or manual, only in case of total disconnection, ie by removing the cable or turning off the equipment that WAN2 comes into use.

 

Is it a bug, that until today there was no correction? Because I've seen several comments on the same problem here on the forum.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Backup Wan Don't Work-Solution
2020-02-18 12:15:10 - last edited 2021-04-19 11:29:57

@alfredudu 

You either use Link Backup feature to have only 1 WAN enabled and 2nd WAN enabled only after 1st WAN is down, or you tick Enable Application Optimized Routing, so 1 APP works through 1 WAN. From time to time for the app, if it was not online the whole time, IP could be changed, because you have both WAN enabled, it is normal. You can also configure Policy Routing for some APPs to constantly use exact WAN.

Recommended Solution
  1  
  1  
#4
Options
4 Reply
Re:Backup Wan Don't Work
2020-02-17 03:55:02 - last edited 2021-04-19 11:29:57

@alfredudu 

Hello，

I seem to never see such posts， could can help me find these posts link？I would like to have a check.

According to my experience, the link backup doesn't work because of the wrong configuration. May I ask whether you enabled "Enable Load Balancing" in the basic settings?

If we didn't enable this switch, the link backup won't work.

Hope my experience can help you.

 

 

  0  
  0  
#2
Options
Re:Backup Wan Don't Work
2020-02-17 11:38:28 - last edited 2021-04-19 11:29:57

@Scott.Tao 

 

Good morning Scott.Tao

 

Thank you for answering, oh right, yes, the Load Balance box was not checked, but if I check it the ips are constantly changing, each hour is on a different ip, how can I resolve this situation, so that the backup link works, and there is no constant exchange of ips

  0  
  0  
#3
Options
Re:Backup Wan Don't Work-Solution
2020-02-18 12:15:10 - last edited 2021-04-19 11:29:57

@alfredudu 

You either use Link Backup feature to have only 1 WAN enabled and 2nd WAN enabled only after 1st WAN is down, or you tick Enable Application Optimized Routing, so 1 APP works through 1 WAN. From time to time for the app, if it was not online the whole time, IP could be changed, because you have both WAN enabled, it is normal. You can also configure Policy Routing for some APPs to constantly use exact WAN.

Recommended Solution
  1  
  1  
#4
Options
Re:Backup Wan Don't Work
2020-02-18 23:09:33 - last edited 2021-04-19 11:29:57

@Mitya 

 

It was exactly what was done, creating two routing rules for each WAN, thus allowing to link or backup backup

  0  
  0  
#5
Options

Information

Helpful: 0

Views: 1469

Replies: 4

Related Articles
wan to lan connections for internal use don't work
479 0
Does MR400 work with ER605 on one of the WAN ports as Backup
372 0
Omada ER605 LINK BACKUP confuses primary WAN and Backup WAN
441 0
 WAN backup
1158 0
ER605 No backup wan option available
624 0
Auto Backup failing- need this to work
1124 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.