Business Community > WiFi > EAP-225 Outdoor Mesh wired to indoor EAP
< WiFi

EAP-225 Outdoor Mesh wired to indoor EAP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP-225 Outdoor Mesh wired to indoor EAP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP-225 Outdoor Mesh wired to indoor EAP
EAP-225 Outdoor Mesh wired to indoor EAP
2021-02-09 03:04:50 - last edited 2021-02-09 06:44:00

Hello,

 

I'm looking to set up some Omada equipment between two units and was interested to know if this configuration would work. Both would have EAP-225 Outdoors in mesh mode to connect to each other wirelessly. All solid lines are wired.

 

My main question is would the OC200 be able to manage and monitor the "EAP-225 In2"?

 

 

 

  0      
 
  0      
 
#1
Options
4 Reply
Re:EAP-225 Outdoor Mesh wired to indoor EAP
2021-02-09 06:43:47 - last edited 2021-02-09 06:44:00

Dear @yum,

 

I'm looking to set up some Omada equipment between two units and was interested to know if this configuration would work. Both would have EAP-225 Outdoors in mesh mode to connect to each other wirelessly. All solid lines are wired.

My main question is would the OC200 be able to manage and monitor the "EAP-225 In2"?

 

 

The answer is YES.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:EAP-225 Outdoor Mesh wired to indoor EAP
2021-02-11 16:06:59 - last edited 2021-02-11 16:08:59

@yum 200ft is viable for an ethernet cable.  Presumably there is a physical reason not to to that? E.g. you have to cross a road or similar.

  0  
  0  
#3
Options
Re:EAP-225 Outdoor Mesh wired to indoor EAP
2021-02-12 19:36:39 - last edited 2021-02-12 19:37:07

Hi @yum,

 

I'm not convinced you're going to get 200' between two EAP225-Outdoor with the stock antennas.  The MESH network from the Ethernet connected master node (on left) to the wirelessly connected MESH node on the right uses the 5.8GHz band.

 

I know I only get ~50'-100' from my EAP225-Outdoors on 5.8GHz but that's from AP to STA.  AP to AP will be farther.

 

Beyond 100' you may do better with a CPE710

https://www.amazon.com/TP-Link-Transmission-Wireless-Injector-CPE710/dp/B08D71HC9L/ref=sr_1_1?dchild=1&keywords=cpe710&qid=1613158500&sr=8-1

 

-Jonathan

  0  
  0  
#4
Options
Re:EAP-225 Outdoor Mesh wired to indoor EAP
2021-02-12 20:50:14

@Fae 

 

Thanks for the confirmation.

 

@CarbonPepper 

 

Correct. I'd run ethernet if I could, but there is property in between I cannot run it across.

 

@JSchnee21

 

Thanks for the heads up. I've looked at the CPE710, but wasn't sure if it would be wiser to stay within the Omada line to stay compatible with the OC200.

 

 

  0  
  0  
#5
Options

Information

Helpful: 0

Views: 1124

Replies: 4

Related Articles
EAP 225-Outdoor mesh issue
619 0
 Connecting EAP 225 Outdoor onto a Linksys indoor MESH
440 0
 EAP 225 indoor coverage
401 0
 Eap 225 wired connect to MESH
1449 0
 EAP 225 outdoor mesh network
429 0
eap 225 outdoor in disconnect status
718 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.