Is it possible in Omada SDN to emulate ONLY a virtual LAN-Cable via VLAN?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Is it possible in Omada SDN to emulate ONLY a virtual LAN-Cable via VLAN?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Is it possible in Omada SDN to emulate ONLY a virtual LAN-Cable via VLAN?
Is it possible in Omada SDN to emulate ONLY a virtual LAN-Cable via VLAN?
2022-03-20 09:26:21

Hi there,

 

I would like to have a VLAN, which I only use for test purposes.
There should be no internet connection and no DHCP administration.

Each switch should be assigned a port that uses VLAN999.
So to speak, a virtual LAN cable is to be emulated.

For example, if I plug a NAS into switch 1 on the VLAN999 port, is to be accessed on switch 2 on the VLAN999 port via laptop, but without an automatic DHCP address assignment etc...


It is also not intended to be integrated into Omada, the Omada SDN is only supposed to provide the virtual LAN cable.

Is that somehow possible?
When I create a VLAN, I always have to assign a "LAN Interface" and a "Gateway".
Thanks :)
 

  0      
  0      
#1
Options
6 Reply
Re:Is it possible in Omada SDN to emulate ONLY a virtual LAN-Cable via VLAN?
2022-03-21 07:59:29

Dear @lukass2000 ,

 

lukass2000 wrote

I would like to have a VLAN, which I only use for test purposes.

There should be no internet connection and no DHCP administration.

Each switch should be assigned a port that uses VLAN999.
So to speak, a virtual LAN cable is to be emulated.

For example, if I plug a NAS into switch 1 on the VLAN999 port, is to be accessed on switch 2 on the VLAN999 port via laptop, but without an automatic DHCP address assignment etc...

 

If you want no network access within the LAN, no DHCP server for each VLAN and static IPs for each device, then you just need to be careful to set only the VLANs and not the interfaces.
Note that each port connected to the switches is tagged with all VLANs (just set the VLAN, not the VLAN interface), and then set the port VLAN settings according to the client device.
You can refer to the following articles:

How to configure 802.1Q VLAN on TP-Link Easy Smart/Unmanaged Pro Switches?

How to configure 802.1Q VLAN on Smart and Managed switches using the new GUI?

 

Best Regards!

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#3
Options
Re:Is it possible in Omada SDN to emulate ONLY a virtual LAN-Cable via VLAN?
2022-03-21 14:44:38

  @Hank21 

 

Okay, think tht could work :)
Have it configurated now so

 

 


But if i switch now a device to the Port with use VLAN111, than it is also listed in the "Clients List" from Omada Controller.
Is it correct that way?
Will the devices be listed even if the VLAN have Port Isolation?

Greetings :)

 

  0  
  0  
#4
Options
Re:Is it possible in Omada SDN to emulate ONLY a virtual LAN-Cable via VLAN?
2022-03-22 06:25:57

Dear @lukass2000

 

But if i switch now a device to the Port with use VLAN111, than it is also listed in the "Clients List" from Omada Controller.
Is it correct that way?
Will the devices be listed even if the VLAN have Port Isolation?

 

Yes, it is correct. The clients will be still listed.

 

Best Regards!

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options
Re:Is it possible in Omada SDN to emulate ONLY a virtual LAN-Cable via VLAN?
2022-03-23 08:49:09 - last edited 2022-03-23 08:49:51

@Hank21 

Okay, thanks :)

But the configuration as seen on the screenshots, is right, or?

  0  
  0  
#6
Options
Re:Is it possible in Omada SDN to emulate ONLY a virtual LAN-Cable via VLAN?
2022-03-24 06:42:49

Dear @lukass2000 ,

 

lukass2000 wrote
But the configuration as seen on the screenshots, is right, or?

 

Correct, but you can choose the port is Tagged or Untagged that you want.

 

Best Regards!

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#7
Options
Re:Is it possible in Omada SDN to emulate ONLY a virtual LAN-Cable via VLAN?
2022-03-24 07:10:21
But you can't choose tagged or untagged? The Vlan "Fritzbox" is greyed out?
  0  
  0  
#9
Options