Problem with Archer AX55 (AX3000) and Remote Desktop
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.Problem with Archer AX55 (AX3000) and Remote Desktop
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello Community.
I have an Archer AX55 v1.0 (AX3000) Router with Firmware 1.1.8 Build 20230304 rel.60634(5553)
The problem is that I have to configure it to reset a couple of times a day since it won't let me access a server via remote desktop.
If I reset the router, I can immediately access the server via remote desktop.
Thank you so much
Hola Comunidad.
Tengo un Router Archer AX55 v1.0 (AX3000) con el Firmware 1.1.8 Build 20230304 rel.60634(5553)
El problema es que debo configurarlo para que se resetee un par de veces al dia ya que no me deja ingresar a un servidor a traves del escritorio remoto.
Si reseteo el router, inmediatamente puedo acceder al seridor a traves del escritorio remoto.
Muchas gracias
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi,
Are your computer and the server both in the LAN network of the Archer AX55? and are they connected via LAN cable or via WiFi?
When the problem happens, please don't restart the router next time, instead, please check if internet still works fine on the router and the two devices.
You could also try to ping the server IP address on your computer to see if ping still works, which could confirm whether they are still able to communicate with each other at that moment.
- Copy Link
- Report Inappropriate Content
Hi Sunshine!
Thank you very much for answering.
The server is connected to the Router by ethernet cable. They are in the same network (192.168.1.xxx)
The funny thing is that it does not let me enter (until I restart the router) only if it is through Remote Desktop.
If I enter the server through AnyDesk or TeamViewer, I don't have any problem.
Thank you
- Copy Link
- Report Inappropriate Content
Hi, Anydesk and Teamviewer doesn't require being within the same LAN, so when the Remote Desktop stops working, please check if ping still works which is to confirm if they are still able to communicate with each other within the same LAN.
- Copy Link
- Report Inappropriate Content
Sorry I haven't responded before, I was dealing with certain issues.
I tell you, if I PING from a PC within the local network (192.168.1.xxx) to the server that is connected to a fixed IP (190.15.212.xxx), it responds correctly.
If I am in my office with an IP from my internet provider (200.14.333.xxx), it tells me "timed out" So I don't know how to answer your question.
Thank you so much.
Disculpame que no he respondido antes, estuve con ciertos asuntos.
Te comento, si hago el PING desde una PC dentro de la red local (192.168.1.xxx) hacia el servidor que esta conectado a una IP fija (190.15.212.xxx), me responde correctamente.
Si estoy en mi oficina con una IP de mi proveedor de intrernet (200.14.333.xxx) , me dice "tiempo de espera agotado" Asi que no se cvomo responder a tu pregunta.
Muchas gracias.
- Copy Link
- Report Inappropriate Content
Kind of confused, is 190.15.212.xxx the server IP address? if so, it seems that it is not in your local network since your local network is 192.168.1.x.
- Copy Link
- Report Inappropriate Content
That IP (190.15.212.xxx) is a Fixed IP that the internet provider gives us to be able to access the server from outside the intranet or local network.
- Copy Link
- Report Inappropriate Content
Hi, if you would like to access the server via remote desktop from an external network, you need to configure port forwarding on the router to open port for the Remote Desktop Protocal, if you haven't done that, please refer to this guide:
Port forwarding: how to set up virtual server on TP-Link wireless router?
- Copy Link
- Report Inappropriate Content
A certain port is open, it is not the problem. The problem is that I have to reset the router every XX number of hours because it doesn't always let me access the server.
- Copy Link
- Report Inappropriate Content
Sergio07 wrote
A certain port is open, it is not the problem. The problem is that I have to reset the router every XX number of hours because it doesn't always let me access the server.
Hi, this issue happens only when you are trying to access the server from an external network? or the same when you access the server within the local network?
- Copy Link
- Report Inappropriate Content
Only when I try to access the server from an external network. If I reset the router it is solved for several hours.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1479
Replies: 11
Voters 0
No one has voted for it yet.