Switches
Howdy, I have some new switches of this model, and for some reason that i'm unable to understand, the sfp's are unable to operate at 10gbit, they dont even link to each other, i only have link if i fo
SFP
By
JorgeBastos
· Latest post 2 weeks ago
by JorgeBastos
0Helpful
254Views
Hi there, I have the following setup: ER7412-M2 v1.3 SG3210X-M2 v1.0 with SM5310-T in 1/0/9 (the only 10G BASE-T RJ45 SFP+ Module in this switch!) POE380S connected to Port 9 of the switch, providing
ConfigurationNetwork ConnectivitySFPWPA 2/3
0Helpful
383Views
Inserting a DDM-capable SFP/SFP+ module in an Omada switch adds an enormous 9% load to Omada switch CPUs. Every module adds ~9%! So two DDM modules add ~18% and so on. This seems an unreasonable overh
SFPFirmware UpdateDDM
By
whereisaaron
· Latest post 2026-09-08 18:43:20
by fraroy
1Helpful
955Views
NOTE: Actual model is ES210X-M2, but I am unable to select it I am experiencing severe packet loss (~95%) when using 1G SFP modules in the SFP+ ports in the ES210X-M2 switch. Tested SFP Modules: TP-Li
SFPNetwork ConnectivityES210X-M2
0Helpful
1286Views
Hi there, I have an issue that seems to have been brought up a few times by others, but there was never an actual resolution so I'm posting in hopes of finding one. I've seemingly tried everything I c
SFP
By
Manned6141
· Latest post 2026-03-14 17:42:52
by Chaotix
11Helpful
8416Views
TL-SG3210XHP-M2 ports 9 and 10 are connected via LAG over DAC to SX3008F ports 7 and 8. Everything mostly "just works" but RX errors are logged on whatever is connected to TL-SG3210XHP-M2 port 9. Chan
SFP
0Helpful
610Views
Two switches SG3452X 1.20 with one TL-SM5310-T RJ45 each, connected to Synology E10G18-T1 and Synology E10G30-T2 respectively. The switches are getting DDM alerts 1-2 times are day. Temperatures of th
SFP
0Helpful
820Views
Hi, I just bought a SG3210XHP-M2 3.0 and 2 SM5310-T to go with it. The logs show they are recognised but they do not work. I connected a device to port 10 and .nothing, no light, link showed down. Whe
SFPNetwork Connectivity
1Helpful
977Views
Hello, SG3428X-M2 v1.20 since firmware 1.20.7 Build 20250328 I had been having an issue where one of my SFP modules that is in a static LAG just drops out and the switch needs to be restarted. i updat
SFPLAG
1Helpful
1482Views
Hi, after updating the firmware on my SG3210X-M2 switch to version 1.0.11, the log on my Omada Software Controller (version 5.15.20.20, Linux/Docker) reported the following warnings and alarms: The vo
Firmware UpdateSFP
1Helpful
1223Views
Today I upgraded my companies oc-300 controller to oc-400 and then started getting this warnings: The rx power of the SFP module on XYZ's port Te1/0/25 is higher than warning point. Should I check the
SFP
0Helpful
2566Views
Hi there! I am about to move from an apartment to a new house soon and I am currently planning the network. I have a pfsense appliance with 4 2.5gbe ports: 2 WANs connected to 2 ISPs, 1 LAN and the la
VLAN & Multi-NetworksNetwork ConnectivityControllerSFP
By
StealthNet
· Latest post 2025-05-07 21:55:16
by GRL
2Helpful
1575Views