Home Network Community > Range Extenders > AC750: "Sent a detection for DHCP" in logfile
< Range Extenders

AC750: "Sent a detection for DHCP" in logfile

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

AC750: "Sent a detection for DHCP" in logfile

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
AC750: "Sent a detection for DHCP" in logfile
AC750: "Sent a detection for DHCP" in logfile
2020-03-06 07:45:34 - last edited 2020-09-21 09:49:01

 

Hi,

 

I successfully installed yesterday (thanks to Kevin) an AC750 RE200 as access point via Ethernet.

To do this, I had to disable automatic IP addressing and chose a fix IP address in my box subnetwork range:

 

 

Device works fine.

This morning I found in the log file of the device a message repeated every minute or so:

 

 

Why?

What should I do to remove this message, please?

Moreover, my Box sez : "RE200 disconnected/connected" every minute or so.

I checked the RE200 in my box interface, its address is correct but shown as "DHCP":

How come? 

Thanks.

 

EDIT

I double checked my box interface and just discovered a third device connected via Ethernet which just doesn't exist (I have only my PC and the RE200 plugged in):

 

HOST002

address 192.168.1.3

manufacturer name: AzurWave Technology

Connected via DHCP.

 

:-(

I'm lost!

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:AC750: "Sent a detection for DHCP" in logfile-Solution
2020-09-21 06:02:46 - last edited 2020-09-21 09:49:01

Yes, just forget about the message.

Since I solved the config problem (I had to understand that there were two types of configuration, badly explained in the doc), the repeater works fine (nearly for one year now).
I wish to add that a TP Link tech TeamLinked my PC and solved the params issue in seconds. Thanks to him.

Recommended Solution
  0  
  0  
#10
Options
10 Reply
Re:AC750: "Sent a detection for DHCP" in logfile
2020-03-07 20:11:41

Up?

  0  
  0  
#2
Options
Re:AC750: "Sent a detection for DHCP" in logfile
2020-03-09 09:22:27 - last edited 2020-03-09 09:37:25

@Desiderius 

 

Thanks for your information. May I know have you enabled the DHCP server on the main router? 

 

Please log in to the web UI of the main router and show us a screenshot of the online devices list. 

 

Or you can show us a screenshot of the DHCP client list page on the main router. 

 

FYI, we did a test at our end, when extender works in AP mode and has a static IP, it will send DHCP request to the DHCP server, but unlike the picture you attached, the extender will receive the packet from the main router(DHCP server) which will assign a new IP address, even though the extender won't use it. Therefore, we suspect that the DHCP server on the main router has not been enabled yet. 

 

Picture attached below.

 

Thanks a lot. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#3
Options
Re:AC750: "Sent a detection for DHCP" in logfile
2020-03-09 10:46:51 - last edited 2020-03-09 10:47:39

Yes I did as it provides the IP address of my PS4 (downstairs)

The one of my boys' PS4 (upstairs) uses the RE200 DHCP server (and works fine).

Here are the pix resquested.

 

 

  0  
  0  
#4
Options
Re:AC750: "Sent a detection for DHCP" in logfile
2020-03-12 07:17:22

@Desiderius 

 

Thanks for your valued reply.

 

It is a little strange, not sure why the extender shows disconnected/connected every minute on the main router, and the system log on the extender itself. 

 

If it is okay for you, we would like to follow up on your case via email, then we can do further analysis and try to figure it out. 

 

Please check your inbox then. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#5
Options
Re:AC750: "Sent a detection for DHCP" in logfile
2020-03-12 07:19:01

@Kevin_Z Yes please.

Thanks.

  0  
  0  
#6
Options
Re:AC750: "Sent a detection for DHCP" in logfile
2020-03-13 06:59:19

@Desiderius 

 

Definitely sure. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#7
Options
Re:AC750: "Sent a detection for DHCP" in logfile
2020-03-13 07:18:23 - last edited 2020-03-13 07:18:57

Man, to me it looks like a programming error.

When dynamic IP addressing is disabled for the device, it should not send such requests (and moreover this slows down a bit the traffic).

  0  
  0  
#8
Options
Re:AC750: "Sent a detection for DHCP" in logfile
2020-09-21 03:48:07

@Desiderius 

 

Hello.

 

I have the exact same issue on a TP link RE220. Is there a follow up / resolution to this?

 

Thanks!

John

  0  
  0  
#9
Options
Re:AC750: "Sent a detection for DHCP" in logfile-Solution
2020-09-21 06:02:46 - last edited 2020-09-21 09:49:01

Yes, just forget about the message.

Since I solved the config problem (I had to understand that there were two types of configuration, badly explained in the doc), the repeater works fine (nearly for one year now).
I wish to add that a TP Link tech TeamLinked my PC and solved the params issue in seconds. Thanks to him.

Recommended Solution
  0  
  0  
#10
Options
Re:AC750: "Sent a detection for DHCP" in logfile
2020-09-22 01:32:02

@Desiderius 

 

Thanks I don't know what Teamlink is  but I'll check in w/support on a new thread.

  0  
  0  
#11
Options

Information

Helpful: 0

Views: 2615

Replies: 10

Related Articles
 DHCP detection failed
5550 0
 AP200 AC750 DHCP scope and other Questions
752 0
 Sent packets = 0
494 0
 Errors at logfile that google can't find...
383 0
 sent information about connecting devices
615 0
AC750 WI-FI
344 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.