New Wired Network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

New Wired Network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
New Wired Network
New Wired Network
2020-12-23 22:34:31
Model: OC200  
Hardware Version: V1
Firmware Version:

Hi guys, please, help.

I have OC200, TL-SG2428P, EAP225 and TL-R605.

I adopted everything. Now I want to create several vlan networks.

I create New LAN. Interface 10.13.50.1/24, configure DHCP Range

 

then I create SSID with VLAN50

 

My EAP225 shows SSID vlan50, I connect to it, but I do not receive IP-address. (It is 169.254.x.x). Why?

I guess, TL-R605 must give it to me. Should I change Profile on switch somehow of what?

 

If I make one of the switch port as untagged 50/pvi 50 by changing profile, I still do not receive any IP-address, if connect there. 

I even check by SSH and I see

#
interface gigabitEthernet 1/0/5
  switchport general allowed vlan 50 untagged
  switchport pvid 50
  no switchport general allowed vlan 1
  dot1x port-control authorized-force
  no spanning-tree bpduflood

  lldp med-status
  loopback-detection config process-mode port-based recovery-mode auto
  loopback-detection
#

 


while my TL-R605 is connected to 

#
interface gigabitEthernet 1/0/3
  switchport general allowed vlan 50-52 tagged
  dot1x port-control authorized-force
  no spanning-tree bpduflood

  lldp med-status
  loopback-detection config process-mode port-based recovery-mode auto
  loopback-detection
#

 

It only give IPs from default range of 192.168.0.1 for the ports like gi1/0/3, which belongs to profile ALL (with vlan 1)
 

  0      
  0      
#1
Options
4 Reply
Re:New Wired Network
2020-12-23 22:38:44

@Mitya I am stupid. I configured everything for LAN, while I was connected to LAN1.

  0  
  0  
#2
Options
Re:New Wired Network
2020-12-23 22:55:11

@Mitya still I have a question though.

I changed Management VLAN for switch, AP and moved my OC200 to untagged vlan 50 port.

Now my TL-R605 is in Disconnected status, because it shows IP 192.168.0.1 and I can't change it to 10.13.50.1/24, and it is not changed automatically in controller.

 

How can I now force my controller to connect to TL-R605 not by 192.168.0.1, but by 10.13.50.1/24, the New LAN Interface, which I created above?

  0  
  0  
#3
Options
Re:New Wired Network
2020-12-24 08:59:50

 Dear @Mitya,

 

Now my TL-R605 is in Disconnected status, because it shows IP 192.168.0.1 and I can't change it to 10.13.50.1/24, and it is not changed automatically in controller.

How can I now force my controller to connect to TL-R605 not by 192.168.0.1, but by 10.13.50.1/24, the New LAN Interface, which I created above?

 

Are you able to ping the router IP 192.168.0.1 on the device which you use to access the OC200?

How is the Profile configured for the Port3 that is connected to the R605 router?

How about the Profile for the Ports that are connected to the AP, Switch and OC200?

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options
Re:New Wired Network
2020-12-24 12:45:10

@Fae In fact, I can ping it from my laptop and OC200 also must be able to do so, however, it is still "heartbeat missed" and then "disconnected".So, Intervlan routing works.

Profile on port for TL-R605 is ALL, so it has vlan 1 untagged/pvid 1 and tagged 50-52 vlans.

OC200 - untagged 50

AP - ALL, so it is tagged 50-52 and untagged 1/pvid 1

Laptop - untagged 50.

 

I thought you can change somehow default IP Interface, which would be checked, but it seems you can't. You know, I seems to fix it by changing default LAN Network from 192.168.0.1/24 to the needed one (vlan 50). So, I didn't create new network with vlan50, but changed default LAN. Then I needed  to reboot it in some weird order and now I have, what I need, but it is very unfriendly, as I could see.

  0  
  0  
#5
Options