EAP225 - LATEST FIRMWARE

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP225 - LATEST FIRMWARE

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP225 - LATEST FIRMWARE
EAP225 - LATEST FIRMWARE
2021-06-15 20:04:00
Model: EAP225  
Hardware Version: V3
Firmware Version: 5.0.0 Build 20200918 Rel. 58628(5553)

I recently bought an EAP225(US) Ver3.8 Access Point. I downloaded what I thought was the most recent firmware here. However, since I upgraded the WIFI range and performance seems to have degraded. My outdoor camera which connected fine before upgrading can barely connect now. Unfortunately, I did not take a note of the firmware which the EAP225 came pre-installed with before I upgraded. There are 3 firmwares at the link I posted above. I have tried all with the same results.

 

There is also this link below with firmware for V3 of the EAP225.

 

Now I'm confused. They both say US in the URL. Which link should I used? 

 

So, are these firmwares for V3 compatible with V3.8 of the Access Point? If they are, then why is my AP performing badly since I upgraded. Is there a special place I need to go to get firmware for my EAP225 v3.8 (US) AP? 

 

Regards.

  0      
  0      
#1
Options
3 Reply
Re:EAP225 - LATEST FIRMWARE
2021-06-16 14:27:32
The latest version is Model: EAP225(US) v3.0 Firmware Version: 5.0.3 Build 20210316 Rel. 67358 https://static.tp-link.com/2021/202104/20210427/EAP225(US)_V3_5.0.3%20Build%2020210316.zip
  0  
  0  
#2
Options
Re:EAP225 - LATEST FIRMWARE
2021-06-19 09:33:38
I'm curious about how far is your camera
  0  
  0  
#3
Options
Re:EAP225 - LATEST FIRMWARE
2021-07-09 07:34:27

Dear @SUPAJ,

 

SUPAJ wrote

I recently bought an EAP225(US) Ver3.8 Access Point. I downloaded what I thought was the most recent firmware here. However, since I upgraded the WIFI range and performance seems to have degraded. My outdoor camera which connected fine before upgrading can barely connect now. Unfortunately, I did not take a note of the firmware which the EAP225 came pre-installed with before I upgraded. There are 3 firmwares at the link I posted above. I have tried all with the same results.

 

There is also this link below with firmware for V3 of the EAP225.

 

Now I'm confused. They both say US in the URL. Which link should I used? 

 

For EAP225(US) Ver3.8, the following firmware download link is correct. ( V3.8 = V3 )

https://www.tp-link.com/us/support/download/eap225/v3/#Firmware

 

Is your EAP225 configured and managed via Omada Controller or via Standalone web UI?

Do you have any advanced features such as Airtime Fairness configured on the EAP225?

May I know the model number of your outdoor camera?

 

If possible, you may factory reset the EAP225 and configure the basic wireless settings with WPA/PSK-AES security for a try.

How to configure basic wireless settings of my TP-Link EAP in Standalone mode: https://www.tp-link.com/us/support/faq/2935/

 

If your concern is resolved, I'd encourage you to give feedback to the community so others can be confident of the solution.

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 2662

Replies: 3

Related Articles