EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs
EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs
2022-07-15 17:41:15
Model: EAP650  
Hardware Version: V1
Firmware Version: 1.0.3 Build 20220316 Rel. 51972

Hello

 

I've recently acquired 2 EAP650 to deploy and replace another WiFi system.

 

While testing the configuration I've come to the issue that  the SSIDs that are on tagged VLANs have much lower throughput.

 

SSID with no VLAN tag(ID 1), guest not enabled: ~500Mbps to WAN

SSID with VLAN tag (ID3),  guest not enabled: ~140Mbps

Tried both with OFDMA enabled / disabled, issue persisted.

 

Connection is as follows:

 

OPNsense (Firewall, Router) - > Port#1 of Switch TL-SG105E (VLAN1 port 1-5 untagged, VLAN 3 port 1 and 5 tagged PVID 1, port 2 untagged PVID 3) -> EAP650 (Switch Port #5)

 

PC on Port#2 of switch for cross check.

PC connected directly via switch on port#2 throughput is as expected, ~500Mbps.

 

EAP directly on Router/Firewall, issue persists.

 

The Omada controller is running on a LXC container.

 

Could this be a firmware issue? I saw another thread regarding TCP protocol issues on 650/653 and 670 EAPs. Any update in the works that could be shared to test?

 

Hopefully this is not an hardware issue, because in that case I'd have to return both EAPs.

  0      
  0      
#1
Options
7 Reply
Re:EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs
2022-07-15 17:49:14

  @s0x Hello,

 

I'm getting approx 670 Mbps on tagged SSID both upload and download speed on 80 MHz wide channel at 5 GHz 802.11ax at EAP653 with last (1.0.1) firmware.

 

Do you have latest firmware? Try iperf between your Wi-Fi device and local wired device.

  0  
  0  
#2
Options
Re:EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs
2022-07-16 00:13:39

  @jrypacek Hi

 

Yes, it's on latest firmware currently publicly available, 1.0.3 Build 20220316 Rel. 51972.

 

I did test with both a 2Gbit LAG and Single 1Gbit port from switch to router/firewall. On all the situations the Wi-Fi client was connected to 5GHz, configured for 80Mhz.

 

SSID with no VLAN TAG (ID: 1), from Wi-Fi client to Wired client:

 

PS C:\> iperf3.exe --client 10.70.70.100
Connecting to host 10.70.70.100, port 5201
[  5] local 10.70.70.103 port 59181 connected to 10.70.70.100 port 5201
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec  72.0 MBytes   603 Mbits/sec
[  5]   1.00-2.00   sec  74.1 MBytes   621 Mbits/sec
[  5]   2.00-3.00   sec  76.4 MBytes   640 Mbits/sec
[  5]   3.00-4.00   sec  78.0 MBytes   655 Mbits/sec
[  5]   4.00-5.01   sec  76.1 MBytes   636 Mbits/sec
[  5]   5.01-6.00   sec  74.4 MBytes   627 Mbits/sec
[  5]   6.00-7.00   sec  79.4 MBytes   666 Mbits/sec
[  5]   7.00-8.01   sec  79.2 MBytes   661 Mbits/sec
[  5]   8.01-9.00   sec  74.0 MBytes   622 Mbits/sec
[  5]   9.00-10.00  sec  80.6 MBytes   676 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.00  sec   764 MBytes   641 Mbits/sec                  sender
[  5]   0.00-10.05  sec   763 MBytes   637 Mbits/sec                  receiver

iperf Done.

 

PS C:\> iperf3.exe --client 10.70.70.100 -u -b 0
Connecting to host 10.70.70.100, port 5201
[  5] local 10.70.70.103 port 56941 connected to 10.70.70.100 port 5201
[ ID] Interval           Transfer     Bitrate         Total Datagrams
[  5]   0.00-1.00   sec  46.2 MBytes   388 Mbits/sec  33200
[  5]   1.00-2.00   sec  44.3 MBytes   372 Mbits/sec  31830
[  5]   2.00-3.00   sec  42.0 MBytes   352 Mbits/sec  30180
[  5]   3.00-4.00   sec  44.8 MBytes   376 Mbits/sec  32200
[  5]   4.00-5.00   sec  46.8 MBytes   393 Mbits/sec  33620
[  5]   5.00-6.00   sec  45.5 MBytes   382 Mbits/sec  32700
[  5]   6.00-7.00   sec  44.0 MBytes   369 Mbits/sec  31630
[  5]   7.00-8.00   sec  45.8 MBytes   384 Mbits/sec  32860
[  5]   8.00-9.00   sec  46.6 MBytes   391 Mbits/sec  33480
[  5]   9.00-10.00  sec  46.2 MBytes   388 Mbits/sec  33190
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Jitter    Lost/Total Datagrams
[  5]   0.00-10.00  sec   452 MBytes   379 Mbits/sec  0.000 ms  0/324890 (0%)  sender
[  5]   0.00-10.05  sec   452 MBytes   378 Mbits/sec  0.056 ms  0/324890 (0%)  receiver

iperf Done.
PS C:\> iperf3.exe --client 10.70.70.100 -b 1K
Connecting to host 10.70.70.100, port 5201
[  5] local 10.70.70.103 port 59900 connected to 10.70.70.100 port 5201
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.01   sec   128 KBytes  1.04 Mbits/sec
[  5]   1.01-2.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   2.01-3.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   3.01-4.00   sec  0.00 Bytes  0.00 bits/sec
[  5]   4.00-5.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   5.01-6.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   6.01-7.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   7.01-8.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   8.01-9.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   9.01-10.01  sec  0.00 Bytes  0.00 bits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.01  sec   128 KBytes   105 Kbits/sec                  sender
[  5]   0.00-10.01  sec   128 KBytes   105 Kbits/sec                  receiver

iperf Done.

SSID with no VLAN TAG (ID: 1), from Wi-Fi client to Wired client, on LAG port:


PS C:\> iperf3.exe --client 10.70.70.100
Connecting to host 10.70.70.100, port 5201
[  5] local 10.70.70.103 port 59193 connected to 10.70.70.100 port 5201
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec  76.1 MBytes   637 Mbits/sec
[  5]   1.00-2.00   sec  81.4 MBytes   683 Mbits/sec
[  5]   2.00-3.00   sec  83.6 MBytes   702 Mbits/sec
[  5]   3.00-4.00   sec  81.8 MBytes   684 Mbits/sec
[  5]   4.00-5.01   sec  76.4 MBytes   639 Mbits/sec
[  5]   5.01-6.00   sec  69.8 MBytes   586 Mbits/sec
[  5]   6.00-7.00   sec  75.4 MBytes   634 Mbits/sec
[  5]   7.00-8.00   sec  79.5 MBytes   666 Mbits/sec
[  5]   8.00-9.00   sec  74.6 MBytes   626 Mbits/sec
[  5]   9.00-10.00  sec  84.9 MBytes   712 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.00  sec   783 MBytes   657 Mbits/sec                  sender
[  5]   0.00-10.05  sec   782 MBytes   653 Mbits/sec                  receiver

iperf Done.

 

PS C:\> iperf3.exe --client 10.70.70.100 -u -b 0
Connecting to host 10.70.70.100, port 5201
[  5] local 10.70.70.103 port 61963 connected to 10.70.70.100 port 5201
[ ID] Interval           Transfer     Bitrate         Total Datagrams
[  5]   0.00-1.00   sec  48.6 MBytes   407 Mbits/sec  34890
[  5]   1.00-2.00   sec  45.1 MBytes   378 Mbits/sec  32410
[  5]   2.00-3.00   sec  47.0 MBytes   394 Mbits/sec  33720
[  5]   3.00-4.00   sec  46.2 MBytes   387 Mbits/sec  33170
[  5]   4.00-5.00   sec  48.5 MBytes   406 Mbits/sec  34810
[  5]   5.00-6.00   sec  49.8 MBytes   418 Mbits/sec  35780
[  5]   6.00-7.00   sec  47.5 MBytes   399 Mbits/sec  34150
[  5]   7.00-8.00   sec  45.7 MBytes   383 Mbits/sec  32820
[  5]   8.00-9.00   sec  48.3 MBytes   406 Mbits/sec  34690
[  5]   9.00-10.00  sec  46.9 MBytes   393 Mbits/sec  33660
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Jitter    Lost/Total Datagrams
[  5]   0.00-10.00  sec   474 MBytes   397 Mbits/sec  0.000 ms  0/340100 (0%)  sender
[  5]   0.00-10.06  sec   473 MBytes   394 Mbits/sec  0.044 ms  679/340100 (0.2%)  receiver

iperf Done.
PS C:\> iperf3.exe --client 10.70.70.100 -b 1K
Connecting to host 10.70.70.100, port 5201
[  5] local 10.70.70.103 port 59958 connected to 10.70.70.100 port 5201
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.01   sec   128 KBytes  1.04 Mbits/sec
[  5]   1.01-2.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   2.01-3.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   3.01-4.00   sec  0.00 Bytes  0.00 bits/sec
[  5]   4.00-5.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   5.01-6.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   6.01-7.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   7.01-8.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   8.01-9.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   9.01-10.00  sec  0.00 Bytes  0.00 bits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.00  sec   128 KBytes   105 Kbits/sec                  sender
[  5]   0.00-10.04  sec   128 KBytes   104 Kbits/sec                  receiver

iperf Done.

SSID with VLAN TAG (ID: 50), from Wi-Fi client to Wired client:

 

PS C:\> iperf3.exe --client 192.168.50.101
Connecting to host 192.168.50.101, port 5201
[  5] local 192.168.50.103 port 59474 connected to 192.168.50.101 port 5201
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec  21.5 MBytes   180 Mbits/sec
[  5]   1.00-2.00   sec  22.6 MBytes   190 Mbits/sec
[  5]   2.00-3.00   sec  23.1 MBytes   194 Mbits/sec
[  5]   3.00-4.01   sec  18.9 MBytes   158 Mbits/sec
[  5]   4.01-5.00   sec  18.0 MBytes   152 Mbits/sec
[  5]   5.00-6.00   sec  18.2 MBytes   153 Mbits/sec
[  5]   6.00-7.00   sec  19.1 MBytes   160 Mbits/sec
[  5]   7.00-8.00   sec  25.9 MBytes   218 Mbits/sec
[  5]   8.00-9.00   sec  27.9 MBytes   234 Mbits/sec
[  5]   9.00-10.00  sec  27.1 MBytes   227 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.00  sec   222 MBytes   186 Mbits/sec                  sender
[  5]   0.00-10.06  sec   222 MBytes   185 Mbits/sec                  receiver

iperf Done.

PS C:\> iperf3.exe --client 192.168.50.101 -u -b 0
Connecting to host 192.168.50.101, port 5201
[  5] local 192.168.50.103 port 52152 connected to 192.168.50.101 port 5201
[ ID] Interval           Transfer     Bitrate         Total Datagrams
[  5]   0.00-1.00   sec  46.1 MBytes   386 Mbits/sec  33100
[  5]   1.00-2.00   sec  43.9 MBytes   368 Mbits/sec  31500
[  5]   2.00-3.00   sec  44.9 MBytes   376 Mbits/sec  32220
[  5]   3.00-4.00   sec  45.5 MBytes   382 Mbits/sec  32660
[  5]   4.00-5.00   sec  47.1 MBytes   395 Mbits/sec  33810
[  5]   5.00-6.00   sec  47.3 MBytes   397 Mbits/sec  33960
[  5]   6.00-7.00   sec  48.1 MBytes   404 Mbits/sec  34580
[  5]   7.00-8.00   sec  47.3 MBytes   397 Mbits/sec  33970
[  5]   8.00-9.00   sec  45.4 MBytes   381 Mbits/sec  32600
[  5]   9.00-10.00  sec  48.2 MBytes   404 Mbits/sec  34590
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Jitter    Lost/Total Datagrams
[  5]   0.00-10.00  sec   464 MBytes   389 Mbits/sec  0.000 ms  0/332990 (0%)  sender
[  5]   0.00-10.05  sec   255 MBytes   213 Mbits/sec  0.083 ms  149690/332988 (45%)  receiver

iperf Done.
PS C:\> iperf3.exe --client 192.168.50.101 -b 1K
Connecting to host 192.168.50.101, port 5201
[  5] local 192.168.50.103 port 59589 connected to 192.168.50.101 port 5201
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.01   sec   128 KBytes  1.04 Mbits/sec
[  5]   1.01-2.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   2.01-3.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   3.01-4.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   4.01-5.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   5.01-6.00   sec  0.00 Bytes  0.00 bits/sec
[  5]   6.00-7.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   7.01-8.00   sec  0.00 Bytes  0.00 bits/sec
[  5]   8.00-9.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   9.01-10.01  sec  0.00 Bytes  0.00 bits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.01  sec   128 KBytes   105 Kbits/sec                  sender
[  5]   0.00-10.05  sec   128 KBytes   104 Kbits/sec                  receiver

iperf Done.

SSID with VLAN TAG (ID: 50), from Wi-Fi client to Wired client, on LAG port:

PS C:\> iperf3.exe --client 192.168.50.101
Connecting to host 192.168.50.101, port 5201
[  5] local 192.168.50.103 port 59484 connected to 192.168.50.101 port 5201
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec  19.5 MBytes   163 Mbits/sec
[  5]   1.00-2.00   sec  22.1 MBytes   185 Mbits/sec
[  5]   2.00-3.00   sec  22.4 MBytes   188 Mbits/sec
[  5]   3.00-4.00   sec  23.4 MBytes   196 Mbits/sec
[  5]   4.00-5.01   sec  22.9 MBytes   191 Mbits/sec
[  5]   5.01-6.00   sec  22.6 MBytes   190 Mbits/sec
[  5]   6.00-7.01   sec  22.4 MBytes   187 Mbits/sec
[  5]   7.01-8.00   sec  23.2 MBytes   195 Mbits/sec
[  5]   8.00-9.00   sec  24.6 MBytes   207 Mbits/sec
[  5]   9.00-10.00  sec  23.0 MBytes   193 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.00  sec   226 MBytes   190 Mbits/sec                  sender
[  5]   0.00-10.07  sec   226 MBytes   188 Mbits/sec                  receiver

iperf Done.

 

PS C:\> iperf3.exe --client 192.168.50.101 -u -b 0
Connecting to host 192.168.50.101, port 5201
[  5] local 192.168.50.103 port 62021 connected to 192.168.50.101 port 5201
[ ID] Interval           Transfer     Bitrate         Total Datagrams
[  5]   0.00-1.00   sec  41.9 MBytes   352 Mbits/sec  30120
[  5]   1.00-2.00   sec  45.4 MBytes   380 Mbits/sec  32640
[  5]   2.00-3.00   sec  45.9 MBytes   386 Mbits/sec  32940
[  5]   3.00-4.00   sec  45.1 MBytes   378 Mbits/sec  32360
[  5]   4.00-5.00   sec  47.0 MBytes   395 Mbits/sec  33790
[  5]   5.00-6.00   sec  46.2 MBytes   387 Mbits/sec  33160
[  5]   6.00-7.00   sec  46.1 MBytes   387 Mbits/sec  33090
[  5]   7.00-8.00   sec  45.3 MBytes   380 Mbits/sec  32560
[  5]   8.00-9.00   sec  46.5 MBytes   391 Mbits/sec  33420
[  5]   9.00-10.00  sec  46.5 MBytes   390 Mbits/sec  33370
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Jitter    Lost/Total Datagrams
[  5]   0.00-10.00  sec   456 MBytes   382 Mbits/sec  0.000 ms  0/327450 (0%)  sender
[  5]   0.00-10.06  sec   286 MBytes   239 Mbits/sec  0.048 ms  121893/327448 (37%)  receiver

iperf Done.
PS C:\> iperf3.exe --client 192.168.50.101 -b 1K
Connecting to host 192.168.50.101, port 5201
[  5] local 192.168.50.103 port 59575 connected to 192.168.50.101 port 5201
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.01   sec   128 KBytes  1.04 Mbits/sec
[  5]   1.01-2.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   2.01-3.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   3.01-4.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   4.01-5.00   sec  0.00 Bytes  0.00 bits/sec
[  5]   5.00-6.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   6.01-7.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   7.01-8.00   sec  0.00 Bytes  0.00 bits/sec
[  5]   8.00-9.01   sec  0.00 Bytes  0.00 bits/sec
[  5]   9.01-10.00  sec  0.00 Bytes  0.00 bits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-10.00  sec   128 KBytes   105 Kbits/sec                  sender
[  5]   0.00-10.05  sec   128 KBytes   104 Kbits/sec                  receiver

iperf Done.

 

 

  0  
  0  
#3
Options
Re:EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs
2022-07-22 16:51:48

@Fae Hello

 

Any update on the possible issues found by R&D? Also discussed here https://community.tp-link.com/en/business/forum/topic/559240

 

Is there any beta firmware I could test?

 

Thank you

  0  
  0  
#4
Options
Re:EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs
2022-07-28 07:05:29

Dear @s0x,

 

s0x wrote

Any update on the possible issues found by R&D? Also discussed here https://community.tp-link.com/en/business/forum/topic/559240

Is there any beta firmware I could test?

 

Sorry that I haven't been informed of an update on the issue yet. But the R&D team confirmed that they would provide a Beta firmware to fix the issue, I'll let you know once the beta firmware is available. Thank you for your great patience!

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#5
Options
Re:EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs
2022-07-28 13:23:40

  @Fae thank you.

 

Any Eta? Let me know once it's available.

 

  0  
  0  
#6
Options
Re:EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs
2022-08-03 16:53:29

  @Fae Hi

 

Sorry to bother you so much, any news?

 

Since reporting the issue I saw that another customer has opened a topic regarding issues with both EAP 670/653.

 

I also when opening this topic sent a support request via form, but never got any response or information regarding that.

 

Thank you

  0  
  0  
#7
Options
Re:EAP650(Eu) V1 - Lower throughput on tagged VLAN SSIDs
2022-08-04 05:57:07 - last edited 2022-08-04 11:58:44

Dear @s0x,

 

s0x wrote

Sorry to bother you so much, any news?

 

Thank you for your query. It takes some time to work out a solution to the issue.

I've pushed the R&D team to make a beta firmware, will keep you informed in this original post once the beta firmware is ready.

 

Edit: @s0x  the beta firmware has been provided in the mentioned post, please have a check. Thanks for your cooperation and patience!

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#8
Options