Business Community > WiFi > AC1350 Ceiling AP not behaving like other APs connected to controller
< WiFi

AC1350 Ceiling AP not behaving like other APs connected to controller

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

AC1350 Ceiling AP not behaving like other APs connected to controller

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
AC1350 Ceiling AP not behaving like other APs connected to controller
AC1350 Ceiling AP not behaving like other APs connected to controller
2023-02-09 11:29:44 - last edited 2023-02-10 14:06:34
Tags: #VLAN & Multi-Networks
Model: EAP225  
Hardware Version: V3
Firmware Version: 5.0.9

Hi folks,

 

I have a small home network setup. 

The Omada controller is running in a Linux container. 

 

I have an EAP225 ceiling mount AP and an EAP110 v4.0. 

 

When I am connected to the EAP110, everything behaves as normal on my network.  I have 3 VLANS, (VLAN1 - the main LAN, VLAN 90 - A guest network and VLAN 91 for all things IOT).  This tells me that everything is setup correctly and all devices connect as they are supposed to on my network.

 

When I try to connect to the EAP225, I cannot connect to my main network (VLAN1).  It times out trying to obtain an IP address.  I find this very confusing as my EAP110 works fine on the exact same controller.

 

I have tried to RESET the EAP225 and rejoin it via the controller and also tried to hard reset it via the RESET hole on the device (10 seconds holding the button in) but the same issue persists.

 

Does anyone have any thoughts on this issue?

Thanks for your time.

 

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:AC1350 Ceiling AP not behaving like other APs connected to controller-Solution
2023-02-10 12:10:45 - last edited 2023-02-10 14:06:34

Dear @dac88 

 

On Controller SSID settings, HomeNet (VLAN 1 SSID) does not need to enable VLAN. 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#4
Options
4 Reply
Re:AC1350 Ceiling AP not behaving like other APs connected to controller
2023-02-10 05:30:24 - last edited 2023-02-10 05:32:02

Dear  @dac88 

 

What is the firmware of your EAP110? And what is the model number of your switch/router?

 

Please note old EAP110 firmware has a different VLAN working mechanism. See my post in this thread:

Omada Controller 5.8.4 VLAN Setup

 

If possible, please share us the VLAN settings of your switch/router, and SSID VLAN on your Omada controller. That information will help us figure out the issue

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:AC1350 Ceiling AP not behaving like other APs connected to controller
2023-02-10 10:36:50 - last edited 2023-02-10 10:37:29

  @Hank21 

 

Hi, thanks for your response.

 

The EAP110 is a version 4.0 on the 5.0.4 firmware.

 

I am using a pfSense router and a Netgear GS724T switch.

 

My setup was working perfectly until I could access the controller no longer and had to setup a new controller. 

When I adopted the EAP225 on the new controller, my VLAN 1 config stopped working on the EAP225.

 

pfSense VLANs

 

vlan 90 - GuestNet

vlan 91 - IOTNet

 

Netgear VLANs

 

vlan 1 - Default - port 1-24,  untagged

vlan 90 - GuestNet - port 19-24, Tagged

vlan 91 - IOTNet - port 19-24, Tagged

 

Omada Controller

 

SSID info (with VLANs):

GuestNet - vlan 90

HomeNet - vlan 1

IOTNet - vlan92

 

 

This setup was working perfectly, on trying to adopt the EAP225 to the updated Omada controller, my VLAN 1 setup stopped working correctly.

 

 

Many thanks.

  0  
  0  
#3
Options
Re:AC1350 Ceiling AP not behaving like other APs connected to controller-Solution
2023-02-10 12:10:45 - last edited 2023-02-10 14:06:34

Dear @dac88 

 

On Controller SSID settings, HomeNet (VLAN 1 SSID) does not need to enable VLAN. 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#4
Options
Re:AC1350 Ceiling AP not behaving like other APs connected to controller
2023-02-10 14:06:54
Thank you so much, that did the trick.
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 225

Replies: 4

Tags

VLAN & Multi-Networks
Related Articles
Attaching AP to Drop Ceiling Rails
473 0
Cannot adopt mesh ap
158 0
Ceiling mount.
551 0
Pinging other devices in AP mode not possible
306 0
TL-SG1016PE - POE with Ceiling Mount AP EAP265 HD AC1750
647 0
Sloped ceiling mount
63 0
About Us
Press
Copyright © TP-LINK CORPORATION PTE. LTD. All rights reserved.