Business Community > Routers > Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2
< Routers

Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2
Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2
2023-02-16 13:00:55 - last edited 2023-03-06 02:01:37
Model: ER605 (TL-R605)  
Hardware Version: V2
Firmware Version: 2.1.2

Dear TP Link,

 

I was happy to see that the controller software version 5.8 supports custom DDNS. However, when I try to use it I get the error that the url is invalid. I have tried just entering a single word, a full domain, prefixi with http:// or https://, etc. It doesn't seem to accept any entry. My provider requires me to call a https url with as parameters a domain and a token. Can you share how I can do that? Or if not possible, fix it? 

 

Also, it isn't clear to me if next to a timer, the service will also be called if the WAN ip address changes. 

 

Thanks!

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2-Solution
2023-02-27 15:26:37 - last edited 2023-03-06 02:01:37

 

Recommended Solution
  7  
  7  
#4
Options
5 Reply
Re:Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2
2023-02-16 15:03:00

As a sidenote to everyone else visiting this thread, the controller (5.8+) requires the router to support custom DDNS before it will provide the interface to do so. 

 

Currently ER605v1 v1.2.1 does not and so you won't see the interface options for customized DDNS.

<< Paying it forward, one juicy problem at a time... >>
  1  
  1  
#2
Options
Re:Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2
2023-02-27 12:57:48

  @d0ugmac1 I use version 2.1.2, which should support this

  0  
  0  
#3
Options
Re:Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2-Solution
2023-02-27 15:26:37 - last edited 2023-03-06 02:01:37

 

Recommended Solution
  7  
  7  
#4
Options
Re:Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2
2023-03-03 09:45:08

  @Hoamboy 

 

Wow, thanks, I finally got it to work! I never realized that the variables in your example really needed to be included as written (so really [USER]). This works, so thanks for your help.

 

For the TP-Link employees who are reading along, I suggest making this a lot less restrictive. A lot of these DDNS providers only require you to call a URL with a token in it and none of the mentioned variables are required. Maybe give the warning that they are not included, but then allow the user to accept that and create the DDNS provider anyway.

  0  
  0  
#5
Options
Re:Custom DDNS with controller software 5.8 & ER605 V2 with V2.1.2
2023-03-03 09:54:17

  @Deputy 

 

You're welcome mate.

 

Also just found out by luck when I clicked 'Save' a bit too early while still using variables - but it started working.

  0  
  0  
#6
Options

Information

Helpful: 0

Views: 1681

Replies: 5

Related Articles
Custom DDNS not working consistently for ER605
1570 0
ER605 Not working with Software controller
1045 0
Custom DDNS with duckdns in Omada Controler is not working
3020 0
Custom DDNS: cloudfare
687 4
ER605 v.2 L2TP bridge
188 0
Omada controller software not add ER605 device
1478 0
About Us
Press
Copyright © TP-LINK CORPORATION PTE. LTD. All rights reserved.