ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hi, I'm having issues with Port Forwarding with load balancing on ER605 with omada controller.
I have two internet providers, one connect to wan and another to wan/lan1. I use to acess some internal services with Port Forwarding through wan/lan1
Both port are online and balancing is woking fine
To set this configuration I create the rule below
and policy routing to force redirection to wan/lan1 from those ips
internal IP -> IpGroup_Any
Internal IP + Port to IPGroup_any
Everything was working fine, but after upgrade to 2.1.1 when a tried to connect, I have a lot of packages that stay on pending and never got a responde from server inside network. It Seems that those packages are been forwarded to wan instead of wan/lan1. Upgrade to 2.1.2 didn't change this behaviour. If i disable balance and use only one wan everything works fine again
I'm using omada controller to set the config to the ER605
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi All,
TP-Link has released a Beta firmware 2.1.3 which contains a BUG Fixed that Port Forwarding does not take effect under multiple WAN ports.
ER605 V2_2.1.3_Build 20230616 Beta Firmware For Trial (Released on Jun 25th, 2023)
You may take your time to upgrade the 2.1.3 Beta firmware for testing.
- Copy Link
- Report Inappropriate Content
Hi @lemaoCool
What is the version of your Omada Controller? Is it the newest V5.9.9? I'm going to run the test on my end.
If possible, please have a try:
Delete the Port Forwarding/Policy Routing entries on the controller;
Re-login the controller;
Add the Port Forwarding/Policy routing again.
- Copy Link
- Report Inappropriate Content
Hi @Hank21
My Omada Controller is on the newest version 5.9.9
I did all the steps suggested, but the same behavior still happen. Can't access the service with port forwarding and load balance
- Copy Link
- Report Inappropriate Content
Hi @lemaoCool
To better assist you, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. The ticket ID is TKID230327156, please check your email box and ensure the support email is well received. Thanks!
- Copy Link
- Report Inappropriate Content
Hi @Hank21
Thanks for the support Hope the support engineer can find a solution for the problem
I've received the email and already replied
- Copy Link
- Report Inappropriate Content
Hello @lemaoCool ，
lemaoCool wrote
Thanks for the support Hope the support engineer can find a solution for the problemI've received the email and already replied
That's great!
Please feel free to reply to the support email for further follow-up.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@Hank21
I have similar issue using ER605 V2, latest fw 2.1.2 Build 20230210 Rel.62992.
ER605 failed port forward / virtual server, so I can't access my server from outside.
Is there any solutions or work around?
- Copy Link
- Report Inappropriate Content
Hi All,
TP-Link has released a Beta firmware 2.1.3 which contains a BUG Fixed that Port Forwarding does not take effect under multiple WAN ports.
ER605 V2_2.1.3_Build 20230616 Beta Firmware For Trial (Released on Jun 25th, 2023)
You may take your time to upgrade the 2.1.3 Beta firmware for testing.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Yes, both port forwarding and VPN are working now.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2695
Replies: 14
Voters 0
No one has voted for it yet.