Business Community > Routers > ER605 V2 after Upgrade to 2.1.3 shows DISCONNECTED
< Routers

ER605 V2 after Upgrade to 2.1.3 shows DISCONNECTED

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

ER605 V2 after Upgrade to 2.1.3 shows DISCONNECTED

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
16 Reply
Re:ER605 V2 after Upgrade to 2.1.3 shows DISCONNECTED
2023-07-11 18:49:38

  @Clive_A 

I didnt get any mail...sorry

  0  
  0  
#12
Options
Re:ER605 V2 after Upgrade to 2.1.3 shows DISCONNECTED
2023-07-12 01:28:52 - last edited 2023-07-12 05:43:20

Hi @kogan 

We have sent an email from support forum email to your registered email address on our forum. If you don't receive any emails, can you look for it in your junk box?
Email address title: [TP-Link Support]-[TKID230709001] [Forum ID 613972] ER605 V2 after Upgrade to 2.1.3 shows DISCONNECTED

Best Regards! If you are new to the forum, please read: Howto - A Guide to Use Forum Effectively. Read Before You Post. Look for a model? Search your model NOW Beta firmware got some NEW features! Subscribe for the latest update! ☛Download Beta Here☚ ☛ ★ Configuration Guide ★ ☚ ☛ ★ Knowledge Base ★ ☚ ☛ ★ Troubleshooting Manual ★ ☚ (Disclaimer: Short links are used above solely for guidance to TP-Link subdomains and are safe and tracker-free. Exercise caution with short links from non-official members on forums. We are not liable for external content or damage from non-official members' link use.)
  0  
  0  
#13
Options
Re:ER605 V2 after Upgrade to 2.1.3 shows DISCONNECTED
2023-07-12 03:48:50

  @Clive_A 

Hi clive..

Same issue for me after upgrading my ER605 V2 Router to version 2.2.0

Thanks

 

 

  0  
  0  
#14
Options
Re:ER605 V2 after Upgrade to 2.1.3 shows DISCONNECTED
2023-07-12 07:17:28

Hello,

 

I get the same issue. It can be solved by restarting the router (remove the power cord and plug it back in) but after a few hours it does it again.

Current Setup: 1x ER605 v2.0, 1x TL-SG3428X v1.0, 2x TL-SG3210 v3.0, 1x TL-SG2210MP v1.0, 2x EAP670(EU) v1.0
  0  
  0  
#15
Options
Re:ER605 V2 after Upgrade to 2.1.3 shows DISCONNECTED-Solution
2023-07-21 08:02:14 - last edited 2023-07-21 08:02:18

Hi All,

 

A newer 2.1.4 Beta firmware has been released for trial, please follow the post link below for details.

ER605 V2_2.1.4_Build 20230720 Beta Firmware For Trial (Released on July 21st, 2023)

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#16
Options
Re:ER605 V2 after Upgrade to 2.1.3 shows DISCONNECTED
2023-07-23 10:47:37 - last edited 2023-07-23 10:54:27

  @Hank21 

 

unfortunately this "downgrade" isnt the solution.

After restarting Router with 2.1.3 or 2.2.0 it goes to "configurating" state for about 12 Minutes, after that router goes in "disconnected" state.

Router does not allow to "update" firmware whils it is in "configurating" state. please, provide us another solution. I have for example NO possibility to drive 600KM to my customer for reseting the router. 

Controller FW is already 5.11.10

I'll proof, if the same problem also exists on 5.9.32

  0  
  0  
#17
Options
12
Related Articles
ER605 v2.0 disconnected after upgrade Firmware 2.2.0
1019 0
ER605 v.2 L2TP bridge
148 0
EAP610 v1 getting disconnect after ER605 v1 firmware 1.3.0 upgrade
381 0
Failed to upgrade ER605 manually.
876 0
ER605 V2 2.1.4 Downgraded Back to 2.1.3
270 0
ER605 frequently disconnects from OC200 after upgrading to firmware 2.2.0
3050 5
About Us
Press
Copyright © TP-LINK CORPORATION PTE. LTD. All rights reserved.