Business Community > Routers > Controller's URL change on adopted router
< Routers

Controller's URL change on adopted router

Controller's URL change on adopted router

Controller's URL change on adopted router
Controller's URL change on adopted router
Monday - last edited Wednesday
Tags: #Controller
Model: ER605 (TL-R605)  
Hardware Version: V2
Firmware Version: 2.2.6

Hi,

 

I'm looking for a way to change, saved by the device, URL address to controller.

My ER605 is in remote location, already adopted, configured to reach out to the main controller via DDNS. I will change the service provider (ddns) therefore I need to provide new URL addres to the router. 

 

I saw the post:

https://community.tp-link.com/en/business/forum/topic/617096

 

Unfortunately, that CLI command is not supported by ER605 (I've tried).

There is no proper setting for that on device config page (in controller).

This is remote location so I can't use Omada Discovery Utility (not sure if that would work anyway).

 

What's the proper way to address such issue?

 

Cheers

  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:Controller's URL change on adopted router-Solution
Monday - last edited Wednesday

  @RaRu 

 

your only option is to use the discovery utility from a pc on the network at the remote location. you can use option 138 but it only supports ip address and does not work on the router itself,

you can also set Device Management Hostname/IP on the controller in global settings, but not all devices support this feature either. routers do not support it.

 

so my best advice is, borrow a pc at the remote location, connect with teamviewer or something and install omada discovery utility and change that way. you need java 8 installed on the pc to make the program work. the change itself takes 5 minutes.

 

 

 

 

 

Recommended Solution
  0  
  0  
#2
Options
Re:Controller's URL change on adopted router-Solution
Tuesday - last edited Wednesday

  @RaRu 

 

 

I probably should have mentioned it but If the router is connected to a controller, you will not see anything in Omada Tool. It is only when the router cannot connect to the controller that you will see it.

 

 

Recommended Solution
  1  
  1  
#5
Options
6 Reply
Re:Controller's URL change on adopted router-Solution
Monday - last edited Wednesday

  @RaRu 

 

your only option is to use the discovery utility from a pc on the network at the remote location. you can use option 138 but it only supports ip address and does not work on the router itself,

you can also set Device Management Hostname/IP on the controller in global settings, but not all devices support this feature either. routers do not support it.

 

so my best advice is, borrow a pc at the remote location, connect with teamviewer or something and install omada discovery utility and change that way. you need java 8 installed on the pc to make the program work. the change itself takes 5 minutes.

 

 

 

 

 

Recommended Solution
  0  
  0  
#2
Options
Re:Controller's URL change on adopted router
Tuesday

Hi @RaRu 

Thanks for posting in our business forum.

Three ways to adopt the device over the network.

DHCP Option 138, and both VPN and inform URL with the Discovery Utility.

All of them have a FAQ on the step-by-step guidance.

Best Regards! If you are new to the forum, please read: Howto - A Guide to Use Forum Effectively. Read Before You Post. Look for a model? Search your model NOW Official and Beta firmware. NEW features! Subscribe for the latest update! ☛Download Beta Here☚ ☛ ★ Configuration Guide ★ ☚ ☛ ★ Knowledge Base ★ ☚ ☛ ★ Troubleshooting ★ ☚ ● Be kind and nice. ● Stay on the topic. ● Post details. ● Search first. ● Please don't take it for granted. ● No email confidentiality should be violated. ● S/N, MAC, and your true public IP should be mosaiced.
  2  
  2  
#3
Options
Re:Controller's URL change on adopted router
Tuesday

  @Clive_A 

 

I have a problem with Discovery Tool. Tried on two computers, Firewall disabled, connected to network via WiFi as well as cable, Java 1.8_431 as well as 1.8_333.

The tool doesn't show any results. Always empty. In app log file I can only see:

 

2024-12-17 20:11:53.474  WARN 38856 --- [main] c.t.utility.common.omadac.OmadacType     : Failed to load omada.properties
2024-12-17 20:11:55.328  INFO 38856 --- [main] c.t.s.e.t.api.transport.AbstractServer   : Start NettyUdpServer bind /0.0.0.0:29810, export /127.0.0.1:29810
2024-12-17 20:11:55.340  INFO 38856 --- [main] c.t.s.e.t.api.transport.AbstractServer   : Start NettyUdpServer bind /0.0.0.0:19810, export /127.0.0.1:19810
2024-12-17 20:11:55.362  INFO 38856 --- [main] c.t.s.e.t.api.transport.AbstractServer   : Start NettyTcpServer bind /0.0.0.0:29812, export /127.0.0.1:29812
2024-12-17 20:11:55.372  INFO 38856 --- [main] c.t.s.e.t.api.transport.AbstractServer   : Start NettyTcpServer bind /0.0.0.0:29811, export /127.0.0.1:29811
2024-12-17 20:11:55.380  INFO 38856 --- [main] c.t.s.e.t.api.transport.AbstractServer   : Start NettyTcpServer bind /0.0.0.0:29814, export /127.0.0.1:29814
2024-12-17 20:11:55.390  INFO 38856 --- [main] c.t.u.discovery.DiscoveryUtilityRunner   : going start DiscoveryUtility

 

Only FAQ I have found about that doesn't say anything more than How To Install:

https://www.tp-link.com/pl/support/faq/2533/

 

I have found similar topic but no solution:

https://community.tp-link.com/en/business/forum/topic/562242

 

Any idea how to fix that?

 

Cheers

  0  
  0  
#4
Options
Re:Controller's URL change on adopted router-Solution
Tuesday - last edited Wednesday

  @RaRu 

 

 

I probably should have mentioned it but If the router is connected to a controller, you will not see anything in Omada Tool. It is only when the router cannot connect to the controller that you will see it.

 

 

Recommended Solution
  1  
  1  
#5
Options
Re:Controller's URL change on adopted router
Wednesday

Hi @RaRu 
Thanks for posting in our business forum.

RaRu wrote

  @Clive_A 

 

I have a problem with Discovery Tool. Tried on two computers, Firewall disabled, connected to network via WiFi as well as cable, Java 1.8_431 as well as 1.8_333.

The tool doesn't show any results. Always empty. In app log file I can only see:

 

2024-12-17 20:11:53.474  WARN 38856 --- [main] c.t.utility.common.omadac.OmadacType     : Failed to load omada.properties
2024-12-17 20:11:55.328  INFO 38856 --- [main] c.t.s.e.t.api.transport.AbstractServer   : Start NettyUdpServer bind /0.0.0.0:29810, export /127.0.0.1:29810
2024-12-17 20:11:55.340  INFO 38856 --- [main] c.t.s.e.t.api.transport.AbstractServer   : Start NettyUdpServer bind /0.0.0.0:19810, export /127.0.0.1:19810
2024-12-17 20:11:55.362  INFO 38856 --- [main] c.t.s.e.t.api.transport.AbstractServer   : Start NettyTcpServer bind /0.0.0.0:29812, export /127.0.0.1:29812
2024-12-17 20:11:55.372  INFO 38856 --- [main] c.t.s.e.t.api.transport.AbstractServer   : Start NettyTcpServer bind /0.0.0.0:29811, export /127.0.0.1:29811
2024-12-17 20:11:55.380  INFO 38856 --- [main] c.t.s.e.t.api.transport.AbstractServer   : Start NettyTcpServer bind /0.0.0.0:29814, export /127.0.0.1:29814
2024-12-17 20:11:55.390  INFO 38856 --- [main] c.t.u.discovery.DiscoveryUtilityRunner   : going start DiscoveryUtility

 

Only FAQ I have found about that doesn't say anything more than How To Install:

https://www.tp-link.com/pl/support/faq/2533/

 

I have found similar topic but no solution:

https://community.tp-link.com/en/business/forum/topic/562242

 

Any idea how to fix that?

 

Cheers

If you cannot install the software, that's a problem with your system or the Java environment.

There is no fix but use the recommended software and install the proper Java kit/version.

 

This is not something we can fix but you need to debug the environment. I have no issue with my Win10 Pro, 64-bit.

 

Java environment.

 

Best Regards! If you are new to the forum, please read: Howto - A Guide to Use Forum Effectively. Read Before You Post. Look for a model? Search your model NOW Official and Beta firmware. NEW features! Subscribe for the latest update! ☛Download Beta Here☚ ☛ ★ Configuration Guide ★ ☚ ☛ ★ Knowledge Base ★ ☚ ☛ ★ Troubleshooting ★ ☚ ● Be kind and nice. ● Stay on the topic. ● Post details. ● Search first. ● Please don't take it for granted. ● No email confidentiality should be violated. ● S/N, MAC, and your true public IP should be mosaiced.
  2  
  2  
#6
Options
Re:Controller's URL change on adopted router
Wednesday

  @MR.S 

 

Thank you. That was the reason why the tool was not working.

 

Have a nice day,

Cheers.

  0  
  0  
#7
Options

Information

Helpful: 0

Views: 102

Replies: 6

Tags

Controller
Related Articles
how to change IP address of ER605 after adopted by omada controller :
482 0
ER605 IPv6 ACL not working when adopted to controller
1068 0
Change base URL of software controller
110 0
Change IP/Subnet ER605
449 0
URL filtering does not seem to work
2184 1
 change controller inform url/ip
4176 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.