Early Access Hardware Controllers Omada SDN Controller 6.2.10 Pre-Release Firmware (Release on 9th Apr, 2026)
This Article Applies to
OC200(UN)_V1_1.40.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC200(UN)_V2_2.25.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC200(UN)_V3_3.2.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC220(UN)_V1_1.5.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC220(UN)_V2_2.4.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC300(UN)_V1_1.34.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC400(UN)_V1_1.12.11_pre-release (Built-in Omada SDN Controller 6.2.10)
Overview
We hope to offer you the opportunity to experience the new features added in Controller v6.2.10.x in advance, and to allow TP-Link to thoroughly test the firmware in your real network environment and across scenarios before the official release. All feedback is welcome, including reports of successful upgrades.
Release Notes
Version Info
This version of the Controller is fully compatible with the Omada App version 5.2.x.
Supported Device Models
For device models Omada Software Controller supports, refer to the Omada Cloud SDN Platform Compatibility List.
Added support for Access Points: Flex Bridge 5.
New Features
- Added support for Wi-Fi Calling, available at Site > Device Config > AP > Wi-Fi Calling, Site > Network Config > Network Setting > WLAN > Advanced Settings > Wi-Fi Calling. The transmission of voice and text messages over Wi-Fi networks is more stable, and a new accompanying Wi-Fi Calling statistics chart has been added. (Requires EAP firmware support)
- Added support for load balancing across access points, available at Site > Network Config > WLAN > SSID > Advanced Settings > Load Balance, balancing client distribution across access points and frequency bands to improve network performance. (Requires EAP firmware support)
- Added support for SSID Band Steering, available at Site > Network Config > WLAN > SSID > Advanced Settings > Band Steering, the SSID configuration takes precedence over the Site configuration. (Requires EAP firmware support)
- Added support for WLAN Optimization Schedule, available at Site > Network Config > Network Setting > WLAN > WLAN Optimization > Manual WLAN Optimization > Schedule. Configuration can be done by Day, Week, and Month.
- Added support for displaying the AFC acquisition status, available at Device > Device List > AFC. (Requires EAP firmware support)
- Added support for CCI and AP Density charts, available at Site > Dashboard > Wi-Fi > WLAN Optimization. Co-channel interference (CCI) indicates the degree of interference experienced by APs on the same channel, AP density reflecting the deployment status of APs.
- Updated SD-WAN access control logic, Users must have All Sites permissions to view the SD-WAN page. SD-WAN page can be modified by Modify, Viewer only allows viewing, and Block hides.
- Added support for PVST/PVST+/PRST/RPVST+, available at Devices > Device List > Manage Device > Config > Services. The addition of RPVST improves link utilization and fault recovery speed in multi-VLAN scenarios. CIST Priority and MaxHops are not supported in this mode. (Requires Switch firmware support)
- Added support for configuring stack port speed on L3 switches, devices with different stacking port speeds can now form a stack group. Available at Devices > Device Group > Stack Group. (Requires Switch firmware support)
- Update the configuration of SNMPv3, available at Network Config > General Settings > SNMP. Added Security Level, Authentication Mode, Authentication Password, Privacy Mode and Privacy Password configurations. (Requires firmware support, Gateway support will be available in a future firmware release)
- Added support for Cloud Owner Permission Migration, available at Account > User. Local Owner and Cloud Owner users are allowed to migrate Cloud Owner to an invited Cloud user. After a successful migration, the Cloud Access user becomes the new Cloud Owner, and the original Cloud Owner is downgraded to Admin.
Added support for Backup & Restore through Cloud Access, available at Settings > Maintenance.Added support for Manual Upgrade via Cloud Access, available at Settings > System Settings > Manual Upgrade.- Added Description field to Portal Access Control, available at Site > Network Config > Authentication > Portal > Access Config.
- Added support for PPSK configuration on the 6Ghz band, available at Site > Network Config > Network Settings > WLAN > SSID. (Requires EAP firmware support)
- Added support for viewing L3 switch dynamic resources, available at Devices > Device List > Manage Device > Config > General Config. Supports viewing the current device SDM template, current resource usage, total resource utilization, and remaining available resources.
- Added support for static routes in SD-WAN, allowing hubs to configure multiple non-local network routes to enable spoke devices to access hub resources for complex routing scenarios such as third-party devices or remote VPNs, available at Global > SD-WAN. (Requires Gateway firmware support)
Enhancements
- Optimized EAP topology identification for wired clients.
- Automatically modify the Legal DHCP server address and automatically fill in the server IP, available at Network Config > LAN.
- Optimized the entry points for Restore and Migration functions, available at Global View > Settings > Migration > Organization Migration. The Restore function can only restore backup files for the current Controller. Backup files for other Controllers can only be imported via migration.
- Optimized EAP batch configuration experience, available at Site > Devices > Batch Action > Batch Config. The display logic has been adjusted and the configuration result will now be displayed after configuration is complete.
- Optimized the display and sorting of Client and Device list.
- Optimized multiple interactions, now supports drag-and-drop selection of ports, available at Dashboard > Topology > Quick Config > Extend Mode, Port Reboot, Port Isolation and Network Wizard; Network Config > Switch ACL, Port Schedule and OUI Based VLAN.
- Optimized the Quick Setup process and simplify configuration steps.
- Optimized VLAN configuration by adding VLAN configuration to the Switch Port Profile, which in turn optimizes the Port page and VLAN page, improving configuration flexibility, available at Device Config > Switch Ports > Port Profile; Device > Manage Device > Ports; Network Config > LAN; Device Config > Switch Ports > Port Setting.
- Optimized Site Migration, an exit button has been added, the Skip button for the Export Site step has been changed to Next, and the Skip button for Migrate Site has been removed, available at Global View > Settings > Migration > Site Migration.
- Optimized Lock to EAP function, when the Lock AP configured by the Client is offline, the Client can connect to others under the Site.
- Other feature optimizations include improved Cloud Access connection speed, faster page load times, and enhanced Portal authentication page performance.
Notes
- Please note that Controllers on different platforms may vary in features, even if their first three digits of the version code are the same. For example, the Linux Controller currently supports Cluster Mode, but the Windows Controller doesn't support it yet.
- The Omada SDN Controller can only manage specific devices running the supported firmware. Please confirm that your device is compatible with the SDN Controller.
- Since version 5.14.32, the Omada Software Controller no longer supports upgrading from Controller v4.
- To strengthen overall security, we recommend upgrading all devices to the latest firmware.
Firmware Download
Before the Upgrade
(1) Please be sure you have read the Beta Test Agreement before upgrading the Pre-release firmware!
(2) For the sake of insurance, it's always recommended to save a copy of the controller Backup Config file before upgrading or downgrading.
(3) You may follow the following guide to upgrade your Omada Controller. How to Upgrade or Downgrade Omada SDN Controller.
Firmware Download Link
Direct Download
OC200(UN)_V1_1.40.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC200(UN)_V2_2.25.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC200(UN)_V3_3.2.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC220(UN)_V1_1.5.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC220(UN)_V2_2.4.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC300(UN)_V1_1.34.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC400(UN)_V1_1.12.11_pre-release (Built-in Omada SDN Controller 6.2.10)
Additional Information
If somehow you encounter an issue during or after the controller upgrade, it's suggested to contact us with the following info:
- Omada Controller version (previous and current)
- Device Model(s), Hardware and Firmware versions
- (if possible) A copy of the Log file and Backup Config file
If you decide to downgrade the controller before reporting the issue to TP-Link, it's recommended to save a copy of the current Log file and Backup Config file, which could help TP-Link investigate and address the problem quickly.
>> How to get the Log file and Backup Config file for Omada SDN Controller:
-
If your Windows software controller failed to launch, please locate the controller installation path for the Log file.
-
If it's not a launch issue, you can export the Log file and Backup Config file to the local network.
-
For Omada Controller v5.8 or later version,
In the Global View, go to Settings > Maintenance > Backup & Restore > Retained Data Backup, select Settings Only, then click Export for the Backup Config file. On the same page, scroll down to Export for Support, then click Export Running Logs to download the desensitized Log file.
-
For Omada Controller v5.6 or v5.7,
Go to Settings > Maintenance > Backup & Restore > Retained Data Backup, select Settings Only, then click Export for the Backup Config file. On the same page, scroll down to Export for Support, then click Export Running Logs to download the desensitized Log file.
-
For Omada Controller v5.5 or a previous version,
Go to Settings > Maintenance > Backup & Restore > Retained Data Backup, select Settings Only, then click Export for the Backup Config file. Go to Settings > Services > Export Data > Running Log to export the Log file.
-
Update Log
Apr 10th, 2026
Remove point 12&13 from the New Features section.
Apr 9th, 2026
Provide the following firmware:
OC200(UN)_V1_1.40.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC200(UN)_V2_2.25.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC200(UN)_V3_3.2.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC220(UN)_V1_1.5.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC220(UN)_V2_2.4.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC300(UN)_V1_1.34.11_pre-release (Built-in Omada SDN Controller 6.2.10)
OC400(UN)_V1_1.12.11_pre-release (Built-in Omada SDN Controller 6.2.10)
Recommended Threads
EAP7xx Fully Adapted to Omada 6.2 Pre-release Firmware (Released on 23rd Jan, 2026)
ER7206 V2 Pre-Release Firmware for SDN Controller 6.2.X.X (Released on February 12th, 2026)
ER707-M2 V1 Pre-Release Firmware for SDN Controller 6.2.X.X (Released on February 12th, 2026)
ER7406 V1 Pre-Release Firmware for SDN Controller 6.2.X.X (Released on February 12th, 2026)
Omada_Network_Application_V6.2.10.x Pre-Release Firmware (Updated on 3rd Apr, 2026)
Omada Switch Pre-Release FW Preview for SDN Controller 6.2.X.X (Update on Apr, 1st, 2026)
Wish you a happy life and smooth network usage! >Omada US Enterprise Beta Program Launch< >Get the Latest Omada SDN Controller Releases Here< >Experience the Latest Omada EAP Firmware<
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi @Vishlamba
Thanks for posting here.
To understand the situation better, please let us know:
1. What kind of device is the client??
2. How does it connect to the network?
3. Is its Internet access affected?
Vishlamba wrote
OC300 V1 6.2.10
ER7206
Hi, Came across this issue where I keep getting IP conflict messages and then keep getting conflict resolved alerts non stop in a day I am getting 50 to 60 for both Please see the screen shot. Just posting 2 pages as I have, all messages under resolved section of the same IP and same to Mac address.
- Copy Link
- Report Inappropriate Content
1. What kind of device is the client?? Its an PUCK switch from Control4
2. How does it connect to the network? WIFI
3. Is its Internet access affected? No
Thanks
- Copy Link
- Report Inappropriate Content
Hi @Vishlamba
Thanks for the reply.
There are two MAC addresses; are they both PUCK switches?
Do they both connect to the network? Do you configure a static IP address for them, or dynamic IP?
What EAP do you use? Please also give us the model number and firmware version for the EAP.
In addition, we need to know the network topology, which should indicate how the router, switch, and EAP are connected. thanks.
Vishlamba wrote
1. What kind of device is the client?? Its an PUCK switch from Control4
2. How does it connect to the network? WIFI
3. Is its Internet access affected? No
Thanks
- Copy Link
- Report Inappropriate Content
Thank you so much for taking the time to post the issue on the TP-Link community!
It seems to work in that it shows results but crashes every time I run it with the error in the screen shot.
>>>Will the controller generate the corresponding logs?
To better assist you, I've created a support ticket via your registered email address and escalated it to our support engineer to look into the issue. The ticket ID is TKID260425815. Please check your inbox and confirm that the support email was received. Thanks!
MantonL wrote
@Vincent-TP Hi Vincent, I'm having trouble with the wireless LAN Optimization in my oc300 v1. It seems to work in that it shows results but crashes every time I run it with the error in the screen shot.
It then wipes out all the wireless LAN's I have and all the setting I've put in for the Optimization including all the previous successful Optimizations. If I then go back out of the LAN setting and then back in again, they all reappear. In reality thankfully the 10 Wireless SSID's I have don't actually get removed, but they do all disappear until I go out and back on the LANS.
Regards Lee...
- Copy Link
- Report Inappropriate Content
Thank you so much for taking the time to post the issue on the TP-Link community!
To better assist you, I've created a support ticket via your registered email address and escalated it to our support engineer to look into the issue. The ticket ID is TKID260425803. Please check your inbox and confirm that the support email was received. Thanks!
krupier wrote
The WLAN Optimization Manual Schedule does not work for me both with and without Adaptive WLAN Optimization. When I run it manually it works fine.
EAP683 UR(EU) v1.0 - 1.4.50
SG3428X v 1.30 - 1.30.20
ER707-M2 v1.0 - 1.4.1
- Copy Link
- Report Inappropriate Content
Hello, I have got the email with the ticket number. Sent the needed data, will be looking forward to the outcome. Thanks!
- Copy Link
- Report Inappropriate Content
Hi Vincent
I mentioned my issue from https://community.tp-link.com/en/business/forum/topic/859086?replyId=1683046 in https://community.tp-link.com/en/business/forum/topic/862068 and also opened support request.
Before upgrading to the pre-relaease should I wait for outcome of support investigation as logs quite concerning on my OC200 V1.
Kind Regards,
Areg
- Copy Link
- Report Inappropriate Content
@Vincent-TP Hi Vincent, support ticket received, i'll sort as requested with the logs etc...
Regards Lee...
- Copy Link
- Report Inappropriate Content
@Vincent-TP Hi
Thanks for your reply I managed to solve the issue it was the puck switch and a tapo wifi camera thats was set to use tapo hub as a wifi fall back, I just removed the camera from the hub and the problem was solved. Thanks
- Copy Link
- Report Inappropriate Content
Hi @vrtareg
If necessary, support will recommend upgrading to this pre-release version. If you do not need to test the new features of this version for the time being, it is recommended that you do not upgrade and wait for further advice from support.
vrtareg wrote
Hi Vincent
I mentioned my issue from https://community.tp-link.com/en/business/forum/topic/859086?replyId=1683046 in https://community.tp-link.com/en/business/forum/topic/862068 and also opened support request.
Before upgrading to the pre-relaease should I wait for outcome of support investigation as logs quite concerning on my OC200 V1.
Kind Regards,
Areg
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 777
Replies: 22
Voters 0
No one has voted for it yet.