Business Community > Pharos Wireless Bridges > Upgrading all my Pharos v1.x network to 2.0
< Pharos Wireless Bridges

Upgrading all my Pharos v1.x network to 2.0

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
1234

Upgrading all my Pharos v1.x network to 2.0

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
36 Reply
Re:Upgrading all my Pharos v1.x network to 2.0
2017-01-25 16:01:41

R1D2 wrote



Channel width setting 5 MHz now available in Wireless menu (if region set to Test mode, might not be available in certain countries).
Also, extension channel (upper/lower) field is enabled if fixed channel is used in Test mode (was hidden field IIRC):






Wireless survey lets you restrict scan range in client mode (screeny from a CPE510 V1):







Bug still not fixed in PharOS 2.0.0: Spectrum Analysis on CPE210 still displays range 2312 to 2712 MHz instead of 2402 to 2482 MHz as shown in the CPE210's Quick Installation Guide making it hard to find best channels. Either the range or the labels seem to be wrong (reported to TP-Link several times already):






All of there 3 features were available in firmware v1 too. The third one isn't a bug, it really shows the spectrum from 2312 to 2712, I was one of them who requested this feature because in test mode you are able to use channels from 2312 to 2712MHz.

Try to downgrade to v1.3.3 TP_PharOS_1.3.3_160705 and you will see that was the same. Maybe you had very old firmware v1 so there features weren't available.


I update my cpe210(EU) v1.1 with this v2 firmware and alls go fine, but the max allowed power still 11dbm. No possibility of select country or test mode on the main screen after the reset. There is a way to get 27dbm from (EU) hardware version?


Which version did you update? This one? http://static.tp-link.com/TP_PharOS_2.0.0_161117.zip, which option did you select during flashing? Keep settings or restore default? Maybe you can try this one http://static.tp-link.com/CPE210_V2_161102.zip, and don't keep the current settings.
  0  
  0  
#12
Options
Re:Upgrading all my Pharos v1.x network to 2.0
2017-01-25 16:46:21
Nice job R1D2, thanks for the quick and thorough mini-review!

Any indication of beamforming coming back? Any changes with regards to in-situ performance differentials, anyone performed quick tests to check actual throughput compared to previous version?

Here's a quick flashback to CPEs management VLAN tested in beta firmwares back in 2015.. http://forum.tp-link.com/showthread.php?84173-VLAN-transfer-and-management-VLAN-introduction
Now serving finite customer via f(x)=AirTime/∞ on the 5Ghz band :-/
  0  
  0  
#13
Options
Re:Upgrading all my Pharos v1.x network to 2.0
2017-01-25 23:32:20
Hola John, en país elijo la primer opcion Test_mode para que funcione sin limite de canales ni potencia... el foro es en inglés, deberías escribir en esa lengua. Saludos!

----------------------------------------- IN ENGLISH -----------------------------------

Hello John, in Country I choose the first option "Test_mode" to work without limit of channels and power ... the forum is in English, you should write in that language. Regards!
  0  
  0  
#15
Options
Re:Upgrading all my Pharos v1.x network to 2.0
2017-01-26 01:53:25
let us know how it works out for you
Now serving finite customer via f(x)=AirTime/∞ on the 5Ghz band :-/
  0  
  0  
#17
Options
Re:Upgrading all my Pharos v1.x network to 2.0
2017-01-26 05:49:46

thaischumi wrote

The third one isn't a bug, it really shows the spectrum from 2312 to 2712, I was one of them who requested this feature because in test mode you are able to use channels from 2312 to 2712MHz.


I see. But why did TP-Link not implement a selection box with range filters then like they did in CPE510? There you can restrict the range to the ones useable in most countries.

With this "feature" the Spectrum Analysis now is absolutely useless in the EU, where only frequencies 2402 to 2482 MHz (mid-frequency 2412 to 2472 MHz) are allowed. So it is actually no feature for me, but a bug in the EU edition of the CPE210.

In which countries are the other frequencies from test mode allowed?
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#18
Options
Re:Upgrading all my Pharos v1.x network to 2.0
2017-01-26 05:57:00

peppeve wrote

I update my cpe210(EU) v1.1 with this v2 firmware and alls go fine, but the max allowed power still 11dbm. No possibility of select country or test mode on the main screen after the reset. There is a way to get 27dbm from (EU) hardware version?


It's probably restricted in flash (in the ART partition to be exact) like it is in WBS210(EU). I have installed PharosOS 2.0.0 on my WBS210 v1.20 and there is also no country selection and no test mode with limited TX power, although in CPE210(EU) v1.0 there is country selection menu including test mode.
༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#19
Options
Re:Upgrading all my Pharos v1.x network to 2.0
2017-01-26 06:06:00

R1D2 wrote

I see. But why did TP-Link not implement a selection box with range filters then like they did in CPE510? There you can restrict the range to the ones useable in most countries.


Yes I would like to see the selection box too.

In which countries are the other frequencies from test mode allowed?


Nowhere, it is allowed only in testing environment/laboratory. But who cares? :D
  0  
  0  
#20
Options
Re:Upgrading all my Pharos v1.x network to 2.0
2017-01-26 06:18:41

thaischumi wrote

Yes I would like to see the selection box too.


Even better: If they can restrict channel selection and TX power if a certain region is selected, it would be easy to also adjust the range for Spectrum Analysis according to selected region.

Nowhere, it is allowed only in testing environment/laboratory. But who cares? :D


Regulation authorities. Fines in Germany are in the range of 3,000 to 6,000 Euro and are imposed often, but mainly for exceeding TX power with amplifiers (which are sold freely). You can see their investigation teams in action here an there: :eek:



༺ 0100 1101 0010 10ཏ1 0010 0110 1010 1110 ༻
  0  
  0  
#21
Options
Re:Upgrading all my Pharos v1.x network to 2.0
2017-01-26 21:46:12
Don´t worry... i share this because i do the test and work in all my Pharos CPE210, CPE220 and WBS210 v1.0, v1.1, v1.20...
  0  
  0  
#22
Options
Re:Upgrading all my Pharos v1.x network to 2.0
2017-01-26 21:46:50

Johnsontp wrote

I will update the firmware of my CPE210 V1.1 to Pharos 2.0 although TP Link says there may be damage.


Don´t worry... i share this because i do the test and work in all my Pharos CPE210, CPE220 and WBS210 v1.0, v1.1, v1.20...



[COLOR=#3E3E3E]
  0  
  0  
#23
Options
1234
Related Articles
Do my network once and for all,
284 0
swithed from zte h2981 v.1 to tplink not working...
172 0
Pharos - find IP address on network
327 0
I want to home net work
383 0
Upgrading my Jetstream Switch Firmware
121 0
Deco M5 V1 beta firmware 1.5.0 downgrade to 1.4.x
5311 0
About Us
Press
Copyright © TP-LINK CORPORATION PTE. LTD. All rights reserved.