Omada Controller Not updating the AP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Omada Controller Not updating the AP

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Omada Controller Not updating the AP
Omada Controller Not updating the AP
2020-03-10 05:34:50 - last edited 2020-03-11 04:51:18
Model: EAP320  
Hardware Version: V1
Firmware Version:

Dear Support,

 

 

I created a SSID for WifiTest in Omada controller and i deleted sfter we finish testing but until now there are still client connected to the SSID that already deleted. We already restart the controller and the server pc for EAP controller how many times but still SSID exist.   It means the AP is not updating the configuration from Omada controller.

 

Hope that u will address this problem.

 

Thanks,

 

Magenta

  0      
  0      
#1
Options
2 Accepted Solutions
Re:Omada Controller Not updating the AP-Solution
2020-03-11 04:51:07 - last edited 2020-03-11 04:51:18

@Forrest 

Thank you so much TP Link Support.....

 

Problem solved.....   

 

 

Recommended Solution
  0  
  0  
#9
Options
Re:Omada Controller Not updating the AP-Solution
2020-03-11 07:20:39 - last edited 2020-03-11 07:20:49
@Pascal Update the firmware of all AP in latest version first. Step what I did in Omada controller. 1. In Wireless Settings there is WLAN group (Default) in Default WLAN there is 3 SSID ( MPV-WiFi , MPV-CAM, ITSupport) and I deleted that all SSID. 2. Then I make another WLAN group name: (Magenta) I created 3 SSID also ( MPV-WiFi , MPV-CAM, ITSupport) 3. Deleted all the SSID and the (Magenta) WLAN Group name. 4. Now only Default WLAN Group is in the Controller and make same SSID( MPV-WiFi , MPV-CAM, ITSupport) - See all ap is configure , provisioning and connected status.
Recommended Solution
  0  
  0  
#11
Options
10 Reply
Re:Omada Controller Not updating the AP
2020-03-10 08:46:51

@Joem042379 

 

What's the version of your Omada Controller? We recommend you use the latest version.

Besides, do you try to reset the EAP? If not, please have a try. 

 

  1  
  1  
#2
Options
Re:Omada Controller Not updating the AP
2020-03-10 08:50:10

@forrest 

 

Version for Omada Controller 3.2.7 the Latest version...

  0  
  0  
#3
Options
Re:Omada Controller Not updating the AP
2020-03-10 08:57:18 - last edited 2020-03-10 09:00:06

@Joem042379 @forrest 

 

What append if you ask a manual reconnect with the device that is still showed as connected to this deleted SSID ?
seems to be same issue than me
OC200 don't refresh the list of users or show obsolete state of connection.

  0  
  0  
#4
Options
Re:Omada Controller Not updating the AP
2020-03-10 09:53:06
@Pascal Even we disconnect devices after we scan the wifi still SSID is there and we can connect to that SSID.. how many time we reboot the AP and the controller.
  0  
  0  
#5
Options
Re:Omada Controller Not updating the AP
2020-03-10 10:06:08

@Joem042379 

 

How about resetting the EAP on the Controller? 

I guess there is something wrong when the configuration is issued, you can try to forget the AP on the Omada Controller, 

You can try to forget the AP on the Controller, and check if the issue still exists, please tell us. 

Note: If you forget the AP on the Controller, these AP will disconnect from the Controller for about one or two minutes. 

 

  0  
  0  
#6
Options
Re:Omada Controller Not updating the AP
2020-03-10 10:09:08
OK, definitly not the same issue here
  0  
  0  
#7
Options
Re:Omada Controller Not updating the AP
2020-03-10 10:17:43
@forest I will forget all the 400AP? then I will adopt again? and I will rename 1 by 1? is that a right procedure? we have schedule reboot for all ap.... and they are rebooted successfully so it means once u create a configuration in controller it must be updated all to the AP.. I tried also to assigned and change vlan ID to my existing SSID and it is also updated to the AP. My problem only is why the Old SSID is not deleted in the AP? if other configuration is updated to AP.... Hope u get my points...
  0  
  0  
#8
Options
Re:Omada Controller Not updating the AP-Solution
2020-03-11 04:51:07 - last edited 2020-03-11 04:51:18

@Forrest 

Thank you so much TP Link Support.....

 

Problem solved.....   

 

 

Recommended Solution
  0  
  0  
#9
Options
Re:Omada Controller Not updating the AP
2020-03-11 06:54:16

@Joem042379 

May I know what was the solution ?

 

Forget 400 AP & RE-Adopt them ? surprise

  0  
  0  
#10
Options
Re:Omada Controller Not updating the AP-Solution
2020-03-11 07:20:39 - last edited 2020-03-11 07:20:49
@Pascal Update the firmware of all AP in latest version first. Step what I did in Omada controller. 1. In Wireless Settings there is WLAN group (Default) in Default WLAN there is 3 SSID ( MPV-WiFi , MPV-CAM, ITSupport) and I deleted that all SSID. 2. Then I make another WLAN group name: (Magenta) I created 3 SSID also ( MPV-WiFi , MPV-CAM, ITSupport) 3. Deleted all the SSID and the (Magenta) WLAN Group name. 4. Now only Default WLAN Group is in the Controller and make same SSID( MPV-WiFi , MPV-CAM, ITSupport) - See all ap is configure , provisioning and connected status.
Recommended Solution
  0  
  0  
#11
Options

Information

Helpful: 0

Views: 3554

Replies: 10

Related Articles