Home

Forums

Stories

Knowledge Base

Business Community > All Threads > New to networking

< All Threads

New to networking

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

New to networking

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

New to networking

QHIINC

2020-10-09 18:52:20 - last edited 2022-04-27 01:01:55

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2020-10-09

New to networking

2020-10-09 18:52:20 - last edited 2022-04-27 01:01:55

Model: TL-SG108E

Hardware Version: V4

Firmware Version: 4.6

Hello Everyone! ...

I have a Synology NAS (DS1520+) and am doing ling aggregation using 802.3ad, so four of my 1GB ports are now bonded together.

I purchased the TL-SG108E and am having a hard time configuring it, even though I gave it a static IP address, it cannot be accessed from the internet.

Then it connects DHCP IP 198.162.1.205 and locates it and also has the static IP address I gave it - either way, I finally got it.

*** WHEW ***

The question, DOES THE TL-SG108E support 802.3ad and can create the link aggregation the Synology NAS needs to bond all 4 1GB ports together?

Has someone done this before?

Thanks, everyone in adbamce!

Christopher

1 Accepted Solution

Fae

2020-10-10 06:12:21 - last edited 2022-04-27 01:01:55

Posts: 3603

Helpful: 1360

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:New to networking-Solution

2020-10-10 06:12:21 - last edited 2022-04-27 01:01:55

Dear @QHIINC,

DOES THE TL-SG108E support 802.3ad and can create the link aggregation the Synology NAS needs to bond all 4 1GB ports together?

The TL-SG108E is an Easy Smart Switch which only supports Static LAG, you may refer to Page 28 from the UG below to configure it.

https://static.tp-link.com/2020/202009/20200927/1910012769_Easy%20Smart%20Switch_UG.pdf

Kind Note:

1. To get it to work, please make sure the NAS supports Static LAG as well.

2. Generally speaking, NAS only supports LACP but doesn't support Static LAG, you could confirm this with the support of your NAS.

3. Here is the configuration guide of LAG for your reference, from where you can get the switch models that support LACP.

https://www.tp-link.com/us/configuration-guides/configuring_lag/?configurationId=18204

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Recommended Solution

1 Reply

Fae

2020-10-10 06:12:21 - last edited 2022-04-27 01:01:55

Posts: 3603

Helpful: 1360

Solutions: 474

Stories: 0

Registered: 2020-06-30

Re:New to networking-Solution

2020-10-10 06:12:21 - last edited 2022-04-27 01:01:55

Dear @QHIINC,

DOES THE TL-SG108E support 802.3ad and can create the link aggregation the Synology NAS needs to bond all 4 1GB ports together?

The TL-SG108E is an Easy Smart Switch which only supports Static LAG, you may refer to Page 28 from the UG below to configure it.

https://static.tp-link.com/2020/202009/20200927/1910012769_Easy%20Smart%20Switch_UG.pdf

Kind Note:

1. To get it to work, please make sure the NAS supports Static LAG as well.

2. Generally speaking, NAS only supports LACP but doesn't support Static LAG, you could confirm this with the support of your NAS.

3. Here is the configuration guide of LAG for your reference, from where you can get the switch models that support LACP.

https://www.tp-link.com/us/configuration-guides/configuring_lag/?configurationId=18204

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*

Information

Helpful: 0

Replies: 1

New to networking

New to networking

Information

Voters 0

Tags