Tl-r605 omada controlled properly connected but non visible on Dashboard Omada SDN
Hi,
I've added the new TL-R605 (instead of old 600vpn) on my lan.
Omada SDN (I use hw oc200 as controller) found it properly, (it's always conneced) but on dashboard I can see only my EAP access point.
IN order to see also TL-R605 I have to made every day the speed test.
After this test, the router is visible.
Is there a way to avoid repeating the speed test all the time and keep the tl-r605 visible in the dashboard?
Thanks in advance
Matteo
Before Speedtest
After speedtest
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Dear @Matte,
Is there a way to avoid repeating the speed test all the time and keep the tl-r605 visible in the dashboard?
Try Periodic Speed Test under Site->Services:
- Copy Link
- Report Inappropriate Content
Dear @Matte,
Is there a way to avoid repeating the speed test all the time and keep the tl-r605 visible in the dashboard?
Try Periodic Speed Test under Site->Services:
- Copy Link
- Report Inappropriate Content
I found the checkbox on Site Service to activate the periodic speedtest.
Thanks again for your quickly support.
Matteo
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Dear @Hertog_Jan,
Hertog_Jan wrote
This doesn't seem to work for me using a TL-ER7206 running firmware 1.0.1. No matter how I try to run the speedtest, it fails.
Are you using Omada Software Controller or Omada Hardware Controller, what's the controller version?
Could you please elaborate on the speedtest failed issue? Some screenshots might be helpful.
- Copy Link
- Report Inappropriate Content
@Fae Thanks for the reply.
Fae wrote
Dear @Hertog_Jan,
Hertog_Jan wrote
This doesn't seem to work for me using a TL-ER7206 running firmware 1.0.1. No matter how I try to run the speedtest, it fails.
Are you using Omada Software Controller or Omada Hardware Controller, what's the controller version?
Could you please elaborate on the speedtest failed issue? Some screenshots might be helpful.
I'm using a C200 1.0 hardware controller, Controller Version: 4.3.5, Firmware Version: 1.8.0 Build 20210406 Rel.58757. The Gateway is a TL-ER7206 v1.0, running Firmware version 1.1.0 Build 20210512 Rel.48187.
I'm using the SFP+ port on the gateway, which connects using DHCP and a VLAN. The ethernet WAN port is diabled. Internet works reliably.
I have tried manually running the speedtest, this results in an error:
I have also enabled the periodic speedtest, as some users reported success using that, but that hasn't had any effect for me.
- Copy Link
- Report Inappropriate Content
Dear @Hertog_Jan,
Hertog_Jan wrote
I'm using a C200 1.0 hardware controller, Controller Version: 4.3.5, Firmware Version: 1.8.0 Build 20210406 Rel.58757. The Gateway is a TL-ER7206 v1.0, running Firmware version 1.1.0 Build 20210512 Rel.48187.
I'm using the SFP+ port on the gateway, which connects using DHCP and a VLAN. The ethernet WAN port is diabled. Internet works reliably.
I have tried manually running the speedtest, this results in an error: Test failed. Please try again.
To better assist you, I'd like to escalate your case to the TP-Link support team who could help you more efficiently.
They will reach you via your registered email address shortly, please pay attention to your email box later.
Once the issue is addressed or resolved, I'd encourage you to share it with the community.
Thank you so much for your cooperation and support!
- Copy Link
- Report Inappropriate Content
@Matte TP-Link support did a remote session today, I was pleasantly surprised that they would even go through the trouble to figure out this issue. It seems to have something to do with the speedtest configuration/speedtest API. They changed some internals and were able to run a speedtest. They also reverted the changes and it is broken again. I hope they gathered enough data to fix it! :)
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1629
Replies: 7
Voters 0
No one has voted for it yet.