Business Community > All Threads > EAP245 adopt is failing
< All Threads

EAP245 adopt is failing

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

EAP245 adopt is failing

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
EAP245 adopt is failing
EAP245 adopt is failing
2022-05-29 20:27:28 - last edited 2022-05-30 00:43:10
Model: EAP245  
Hardware Version: V3
Firmware Version: 5.0.5 Build 20220216 Rel. 61848

Hi,

 

yesterday after a firmware update the whole network went down... 
The upgrade was a success towards to 5.0.5 Build 20220216 Rel. 61848
The omada version which I'm using is Omada Controller V3.2.16

 

I'm using Win10 64-bit

 

I always get the fault message "unable to send the adopt command to AP"

 

I opend the port 29814, but it doesn't help, even stopped the firewall, but also nothing...

 

Any good tips for this matter?

  0      
 
  0      
 
#1
Options
2 Reply
Re:EAP245 adopt is failing
2022-05-29 21:45:12 - last edited 2022-05-30 00:43:10

  @Tantie 

 

Hey

 

This is a simple one, you are running the wrong version of AP Firmware for that Controller.

 

Omada controllers running SDN v3.x  can only use older firmware   NOT the latest 5.xxx firmwares as these are designed for SDN v5.xx controllers

 

This link here may help you     https://community.tp-link.com/en/business/forum/topic/264504

 

Your choice is either 

1.  Downgrade the EAP firmware to a version supported on the v3.x controller (see link above)  -   I would NOT recommend this if honest

2.  Upgrade the controller to v4 or v5 but this will require a backup and restore onto the new controller.  It wont automatically update to v4 / v5 via the update wizard as it can break stuff if you are not prepared.  In your case this upgrade is recommended!      Backup the current config, install new v5 controller.. complete basic setup but don't adopt anything.. restore backup..

  1  
  1  
#2
Options
Re:EAP245 adopt is failing
2022-05-30 03:22:09

Dear @Tantie,

 

Tantie wrote

yesterday after a firmware update the whole network went down... 
The upgrade was a success towards to 5.0.5 Build 20220216 Rel. 61848
The omada version which I'm using is Omada Controller V3.2.16

 

Sorry to hear that you have trouble after the firmware update, but @Philbert is right, the EAP firmware is not for your Controller v3.2.16.

 

In fact, the EAP245 firmware 5.0.5 Build 20220216 Rel. 61848 fully adapts the SDN Controller v5, only compatible with V4 or above. Normally, this firmware won't be pushed to the Controller v3 via cloud.

 

Did you download the new firmware from the official website and then upload the firmware for updating on your own?

If yes, have you noticed the release note in red color, or did you just ignore that part?

 

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  1  
  1  
#3
Options

Information

Helpful: 0

Views: 837

Replies: 2

Related Articles
AP FAILING TO ADOPT
415 0
EAP245 - works fine in standalone - when I adopt the SSID disappears
853 0
EAP245 WPS
745 0
EAP245 Disconnecting and won't adopt
4609 0
Omada Software controller v3.2.14 working fine, v4.1.5+ failing to adopt EAPs
938 0
Adopt AP to a Remote Controller?
3842 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.