Business Community > All Threads > Is This Config Possible in TP-Link ER605
< All Threads

Is This Config Possible in TP-Link ER605

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Is This Config Possible in TP-Link ER605

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Is This Config Possible in TP-Link ER605
Is This Config Possible in TP-Link ER605
2022-06-10 10:42:02 - last edited 2022-06-13 02:39:56
Model: ER605 (TL-R605)  
Hardware Version: V6
Firmware Version:

Hi, i want to buy TP-Link ER605 for the following Load Balancing. So, please tell me if the following Config can be done. also i am not so good with networking yet.

 

i have 2 ISP (Lets call them ISP1 and ISP2).

Create 2 VLan(VLan1 = Work Only and VLan2 = Home, Guests, neighbors, etc). Work Systems should have High availability

 

 

My Question is, can this config happen

VLan1 connect to 1) ISP1 as Primary internet and 2) ISP2 as failover and load balance.

VLan2 connect to ISP2 Only. Should not connect to ISP1. So, that Work Systems should not be disturbed 

 

2nd Question,  Can a specific Website to always prefer ISP1 and ISP2 as Failover Only.

 

  0      
 
  0      
 
#1
Options
5 Reply
Re:Is This Config Possible in TP-Link ER605
2022-06-10 19:36:12 - last edited 2022-06-13 02:39:56

  @Shailesh_M 

 

I assume you will be using the Er605 in standalone mode, and not as part of an Omada SDN solution?

<< Paying it forward, one juicy problem at a time... >>
  0  
  0  
#2
Options
Re:Is This Config Possible in TP-Link ER605
2022-06-11 06:53:48 - last edited 2022-06-13 02:39:56

  @d0ugmac1  thank for replying

 

is the 2nd question possible too.

 

and yes, its standalone.

 

Is it possible to confirm this. as i haven't bought it yet. will buy it only if it is possible.

 

 

  0  
  0  
#3
Options
Re:Is This Config Possible in TP-Link ER605
2022-06-12 08:12:09 - last edited 2022-06-13 02:39:56

  @Shailesh_M 

 

I don't use my ER605's in standalone mode, but if Failover mode for the two WANs is good enough for Work users, then have a look at Sections 7.2 and 7.4 in the user guide here:

 

https://static.tp-link.com/upload/manual/2022/202203/20220331/1910013180_ER605&ER7206(UN)_UG.pdf

 

The trick is to use Policy Routing.

<< Paying it forward, one juicy problem at a time... >>
  0  
  0  
#4
Options
Re:Is This Config Possible in TP-Link ER605
2022-06-13 07:18:03

  @Shailesh_M The 1st requirement is not possible if you also wants 2nd requirement. Under my test, if you setup Link Backup, the backup WAN cannot use until the router detect primary WAN offline and switch to backup WAN.

 

But if you don't use Linkbackup and active the two WAN ports together, yes you can reach 2nd requirement with Policy Routing.

  0  
  0  
#5
Options
Re:Is This Config Possible in TP-Link ER605
2022-06-13 10:23:24

  thanks @Somnus for the reply

 

So, following senario will work in right ?

VLan1 connect to 1) ISP1 as Primary internet and 2) ISP2 as failover and load balance.

VLan2 connect to ISP2 Only. Should not connect to ISP1. So, that Work Systems should not be disturbed.

  0  
  0  
#6
Options

Information

Helpful: 0

Views: 762

Replies: 5

Related Articles
Internet Box + TP-Link ER605 router: problem for configuration
1133 0
ER605 Configuration Assistance
862 0
ER605 Configuration Issues
918 0
ER605 firewall config
533 0
Is this allowed: ER605 V1 config to load into ER605 V2 config?
504 0
link er605 to omada without losing configuration.
1247 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.