Super Slow Internet Connection
Super Slow Internet Connection
I have several APs. Often times, on a particular APs (EAP110-Outdoor and EAP610-Outdoor), clients connected to them have a super slow internet connections. I need to reboot them before their internet connections becomes normal. Considering that I have also scheduled a daily reboot of all the APs in the system.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Are any of those problem AP's meshed wirelessly?
Have you engineered your 2.4G wifi channels, or are they all on Auto/Auto?
- Copy Link
- Report Inappropriate Content
Thank you for your reply.
All my APs are wired not meshed wirelessly with auto-channel setup.
If I setup my APs to a certain channel, I will certainly encounter an error after few days that the said channel is already in used by other APs.
- Copy Link
- Report Inappropriate Content
during the slowness... can you confirm the signal strength of the clients? Also confirm the clients are connected to the proper AP?
- Copy Link
- Report Inappropriate Content
Ok, leave your AP channel selection on auto for now, but fix the 2.4G radios to be 20Mhz only. Try that for a few days.
You are obviously operating in a noisy radio area, so you want to concentrate the power of your AP...slight tradeoff in max throughput but significant gains in goodput (I love that term!)
- Copy Link
- Report Inappropriate Content
The signal strenghth is very strong. They are just beside the AP about 5 meters away with no obstruction
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
did you find a fix for this? i have a similar issue.
i purchased the eap110 outdoor in order to have strong wifi connection in an outbuilding. we have a starlink satellite and use the router it came with in the house, with an ethernet connector sharing the connection to the eap110 over about 80meters of cat6wire.
my wifi speed is 150 to 180mbps directly on starlink, but only 20 or 25 mbps from the eap110. i have tested it using a 1meter long cable too. same issue.
when it set it up i used all the standard settings, only named the ssid and password, no other changes. i'm not even sure what to perhaps change. i've ready the manual, watched the videos, and a few videos on youtube.
what setting might need to be changed?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@d0ugmac1 great suggestion. when i plug the cable into my laptop instead of the eap110, there is basically no signal. the computer registers that there is a connection, but it is so weak that the speed test site doens't even activate. i'm ignorant on this overall topic, but am i interpretting correctly that the signal just isn't passing along the cable? the little signal that does pass seems to be boosted and shared better through the eap110 than just what is available on the cable directly.
another commentator said that 100m of outdoor grade cat6 cable is just too long for the signal to pass along. but the reality of the situation is that the starlink is in my house (which is where my powerful solar system is ... we are 100% offgrid), and i can use the computer using either cable or wirelsss just great in the house, and phones on wifi in the house, but i need a connection to be accessible in the outbuilding which is 100m away.
i clearly have no idea what i'm doing here. do you have a suggestion of how to get my starlink signal to an outbuilding 100m away? would using POE cable make a difference, or some kind of signal booster in the house prior to trying to share the signal via cable? is the starlink all-in-one modem and wifi router part of the problem? i think i can use it just as a modem, turn-off/bypass the modem function and replace it with a stronger modem.
i've watched at least 100 videos on youtube trying to figure out what to do so solve this issue. no doubt for a network engineer it is a simple thing, but i don't understand all the technology and lingo sufficiently to always understand the solutions being suggested in the videos i watch.
- Copy Link
- Report Inappropriate Content
Yes, 100m is on the hairy edge of the spec for ethernet, but should work.
Did you do your own connector crimps...if so, you might just want to redo those and see if that makes a difference. Honestly it sounds like a connector problem.
As I recall the 110 is passive 24V POE only, but it doesn't sound like power is the problem, just the quality of the ethernet signal. Did you use shielded cable and/or direct burial grade (ie gel filled)?
Worst case you can run 100m of fibre along the same path, and then figure out a solution to power both the AP and the media converter at the far end. Alternatively you could move the AP a bit closer cable-wise and just use a Repeater at the actual building for better coverage.
If redoing the connectors doesn't help, you could also regenerate the signal as close to the outdoors (at the house) as possible (ie at the outside wall, break the cable, insert an ethernet switch and inject the power after the ethernet switch towards the 110. That might shave enough off the cable length to make a difference.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 1265
Replies: 11