ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
2023-03-13 16:29:37 - last edited 2023-08-16 01:24:29
Model: ER605 (TL-R605)  
Hardware Version: V2
Firmware Version: 2.1.2

 

 

 

 

 

Hi, I'm having issues with Port Forwarding with load balancing on ER605 with omada controller.

 

I have two internet providers, one connect to wan and another to wan/lan1. I use to acess some internal services with  Port Forwarding through wan/lan1

 

Both port are online and balancing is woking fine

 

 

To set this configuration I create the rule below

 

 

and policy routing  to force redirection to wan/lan1 from those ips

 

internal IP -> IpGroup_Any

Internal IP + Port to IPGroup_any

 

 

Everything was working fine, but after upgrade to 2.1.1 when a tried to connect, I have a lot of packages that stay on pending and never got a responde from server inside network.  It Seems that those packages are been forwarded to wan instead of wan/lan1. Upgrade to 2.1.2 didn't change this behaviour. If i disable balance and use only one wan everything works fine again

 

I'm using omada controller to set the config to the ER605

  0      
  0      
#1
Options
1 Accepted Solution
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2-Solution
2023-06-25 08:43:49 - last edited 2023-08-16 01:24:29

 Hi All,

 

TP-Link has released a Beta firmware 2.1.3 which contains a BUG Fixed that Port Forwarding does not take effect under multiple WAN ports.
ER605 V2_2.1.3_Build 20230616 Beta Firmware For Trial (Released on Jun 25th, 2023)

 

You may take your time to upgrade the 2.1.3 Beta firmware for testing.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#9
Options
14 Reply
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
2023-03-14 05:43:05

Hi @lemaoCool 

 

What is the version of your Omada Controller? Is it the newest V5.9.9? I'm going to run the test on my end.

 

If possible, please have a try:

Delete the Port Forwarding/Policy Routing entries on the controller;

Re-login the controller;

Add the Port Forwarding/Policy routing again. 

 

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#2
Options
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
2023-03-14 23:04:53

Hi  @Hank21 

 

My Omada Controller is on the newest version 5.9.9

 

I did all the steps suggested, but the same behavior still happen. Can't access the service with port forwarding and load balance

  0  
  0  
#3
Options
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
2023-03-16 10:37:23

Hi @lemaoCool 

 

To better assist you, I've created a support ticket via your registered email address, and escalated it to our support engineer to look into the issue. The ticket ID is TKID230327156, please check your email box and ensure the support email is well received. Thanks!

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#4
Options
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
2023-03-17 18:12:05

Hi  @Hank21 

 

Thanks for the support Hope the support engineer can find a solution for the problem

 

I've received the email and already replied

  0  
  0  
#5
Options
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
2023-03-20 01:50:56

Hello @lemaoCool

 

lemaoCool wrote

Thanks for the support Hope the support engineer can find a solution for the problem

I've received the email and already replied

 

That's great!

Please feel free to reply to the support email for further follow-up.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#6
Options
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
2023-06-14 12:36:15

  @lemaoCool 

 

 

I have the same issue. Is there a firmware update planned to fix this?

  0  
  0  
#7
Options
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
2023-06-24 05:03:12

  @Hank21 
I have similar issue using ER605 V2, latest fw 2.1.2 Build 20230210 Rel.62992.
ER605 failed port forward / virtual server, so I can't access my server from outside.

Is there any solutions or work around?

  1  
  1  
#8
Options
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2-Solution
2023-06-25 08:43:49 - last edited 2023-08-16 01:24:29

 Hi All,

 

TP-Link has released a Beta firmware 2.1.3 which contains a BUG Fixed that Port Forwarding does not take effect under multiple WAN ports.
ER605 V2_2.1.3_Build 20230616 Beta Firmware For Trial (Released on Jun 25th, 2023)

 

You may take your time to upgrade the 2.1.3 Beta firmware for testing.

Best Regards! >> Omada EAP Firmware Trial Available Here << >> Get the Latest Omada SDN Controller Releases Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#9
Options
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
2023-07-01 03:57:24
Can somenone tell me if with this new firmware is now possible to forward a port with ER605 as a OpenVPN client? Open port - OpenVPN Server - internet - ER 605 as OpenVPN Client - Lan - Web Server por 80. Similar to https://community.tp-link.com/en/smart-home/forum/topic/538506
  0  
  0  
#10
Options
Re:ER605 v2.0 - Port Forwarding with load balancing not working after upgrade to 2.1.1 and 2.1.2
2023-08-19 21:42:18 - last edited 2023-08-19 21:42:35

Yes, both port forwarding and VPN are working now.

  0  
  0  
#11
Options